SLAU367P October 2012 – April 2020 MSP430FR5041 , MSP430FR5043 , MSP430FR50431 , MSP430FR5847 , MSP430FR58471 , MSP430FR5848 , MSP430FR5849 , MSP430FR5857 , MSP430FR5858 , MSP430FR5859 , MSP430FR5867 , MSP430FR58671 , MSP430FR5868 , MSP430FR5869 , MSP430FR5870 , MSP430FR5872 , MSP430FR58721 , MSP430FR5887 , MSP430FR5888 , MSP430FR5889 , MSP430FR58891 , MSP430FR5922 , MSP430FR59221 , MSP430FR5947 , MSP430FR59471 , MSP430FR5948 , MSP430FR5949 , MSP430FR5957 , MSP430FR5958 , MSP430FR5959 , MSP430FR5962 , MSP430FR5964 , MSP430FR5967 , MSP430FR5968 , MSP430FR5969 , MSP430FR5969-SP , MSP430FR59691 , MSP430FR5970 , MSP430FR5972 , MSP430FR59721 , MSP430FR5986 , MSP430FR5987 , MSP430FR5988 , MSP430FR5989 , MSP430FR5989-EP , MSP430FR59891 , MSP430FR5992 , MSP430FR5994 , MSP430FR59941 , MSP430FR6005 , MSP430FR6007 , MSP430FR6035 , MSP430FR6037 , MSP430FR60371 , MSP430FR6041 , MSP430FR6043 , MSP430FR60431 , MSP430FR6045 , MSP430FR6047 , MSP430FR60471 , MSP430FR6820 , MSP430FR6822 , MSP430FR68221 , MSP430FR6870 , MSP430FR6872 , MSP430FR68721 , MSP430FR6877 , MSP430FR6879 , MSP430FR68791 , MSP430FR6887 , MSP430FR6888 , MSP430FR6889 , MSP430FR68891 , MSP430FR6920 , MSP430FR6922 , MSP430FR69221 , MSP430FR6927 , MSP430FR69271 , MSP430FR6928 , MSP430FR6970 , MSP430FR6972 , MSP430FR69721 , MSP430FR6977 , MSP430FR6979 , MSP430FR69791 , MSP430FR6987 , MSP430FR6988 , MSP430FR6989 , MSP430FR69891
The window comparator can monitor data range without CPU interventions. The window comparator is enabled by the SDHSCTL2.WINDMPEN bit. The comparator compares the latest conversion result against the value in the SDHSWINHITH register and the SDHSWINLOTH register, then asserts SDHSRIS.WINHI (window high interrupt flag) if the conversion result is higher than the value in SDHSWINHITH register, or asserts SDHSRIS.WINLO (window low interrupt flag) if the conversion result is lower than the value in SDHSWINLOTH register. The window comparison is always performed with the latest output data before it goes to the internal buffer (see Section 22.2.4 for details about the internal buffer). The window comparison is functional even when the internal buffer is full; however, the internal buffer stops taking new data, so the sample that caused either the SDHSRIS.WINHI or SDHSRIS.WINLO interrupt cannot be read by the SDHSDT register. The application must ensure that the values in the SDHSWINHITH and SDHSWINLOTH registers are in the correct data format. The interrupt flags (WINHI and WINLO) must be reset by user software.