SLUUCF2C January   2021  – May 2022 BQ769142

1.   Read This First
   1.     Battery Monitor Notational Conventions
   2.     Trademarks
   3.     Glossary
2. 1 Introduction
3. 2 Device Description
   1. 2.1 Overview
   2. 2.2 Functional Block Diagram
4. 3 Device Configuration
   1. 3.1 Direct Commands and Subcommands
   2. 3.2 Configuration Using OTP or Registers
   3. 3.3 Data Formats
      1. 3.3.1 Unsigned Integer
      2. 3.3.2 Integer
      3. 3.3.3 Floating Point
      4. 3.3.4 Hex
5. 4 Measurement Subsystem
   1. 4.1  Voltage Measurement
      1. 4.1.1 Voltage Measurement Schedule
      2. 4.1.2 Usage of VC Pins for Cells Versus Interconnect
      3. 4.1.3 Cell Interconnect Resistance
   2. 4.2  General Purpose ADCIN Functionality
   3. 4.3  Coulomb Counter and Digital Filters
   4. 4.4  Synchronized Voltage and Current Measurement
   5. 4.5  Subcommands 0x0071–0x0074 DASTATUS1-4(), Cell Voltage and Synchronized Current Counts
   6. 4.6  Subcommands 0x0075–0x0077 DASTATUS5–7(), Additional Measurements
   7. 4.7  Internal Temperature Measurement
   8. 4.8  Thermistor Temperature Measurement
   9. 4.9  Factory Trim of Voltage ADC
   10. 4.10 Voltage Calibration (ADC Measurements)
   11. 4.11 Voltage Calibration (COV and CUV Protections)
   12. 4.12 Current Calibration
   13. 4.13 Temperature Calibration
6. 5 Primary and Secondary Protection Subsystems
   1. 5.1 Protections Overview
   2. 5.2 Primary Protections
      1. 5.2.1  Primary Protections Overview
      2. 5.2.2  High-Side NFET Drivers
      3. 5.2.3  Protection FETs Configuration and Control
         1. 5.2.3.1 FET Configuration
         2. 5.2.3.2 FET Control
            1. 5.2.3.2.1 PRECHARGE Mode
            2. 5.2.3.2.2 PREDISCHARGE Mode
      4. 5.2.4  Cell Overvoltage Protection
      5. 5.2.5  Cell Undervoltage Protection
      6. 5.2.6  Short Circuit in Discharge Protection
      7. 5.2.7  Overcurrent in Charge Protection
      8. 5.2.8  Overcurrent in Discharge 1, 2, and 3 Protections
      9. 5.2.9  Overtemperature in Charge Protection
      10. 5.2.10 Overtemperature in Discharge Protection
      11. 5.2.11 Overtemperature FET Protection
      12. 5.2.12 Internal Overtemperature Protection
      13. 5.2.13 Undertemperature in Charge Protection
      14. 5.2.14 Undertemperature in Discharge Protection
      15. 5.2.15 Internal Undertemperature Protection
      16. 5.2.16 Host Watchdog Protection
      17. 5.2.17 Precharge Timeout Protection
      18. 5.2.18 Load Detect Functionality
   3. 5.3 Secondary Protections
      1. 5.3.1  Secondary Protections Overview
      2. 5.3.2  Copper Deposition (CUDEP) Permanent Fail
      3. 5.3.3  Safety Undervoltage (SUV) Permanent Fail
      4. 5.3.4  Safety Overvoltage (SOV) Permanent Fail
      5. 5.3.5  Safety Overcurrent in Charge (SOCC) Permanent Fail
      6. 5.3.6  Safety Overcurrent in Discharge (SOCD) Permanent Fail
      7. 5.3.7  Safety Cell Overtemperature (SOT) Permanent Fail
      8. 5.3.8  Safety FET Overtemperature (SOTF) Permanent Fail
      9. 5.3.9  Charge FET (CFETF) Permanent Fail
      10. 5.3.10 Discharge FET (DFETF) Permanent Fail
      11. 5.3.11 Secondary Protector (2LVL) Permanent Fail
      12. 5.3.12 Voltage Imbalance in Relax (VIMR) Permanent Fail
      13. 5.3.13 Voltage Imbalance in Active (VIMA) Permanent Fail
      14. 5.3.14 Short Circuit in Discharge Latched Permanent Fail
      15. 5.3.15 OTP Memory Signature Permanent Fail
      16. 5.3.16 Data ROM Memory Signature Permanent Fail
      17. 5.3.17 Instruction ROM Memory Signature Permanent Fail
      18. 5.3.18 LFO Oscillator Permanent Fail
      19. 5.3.19 Voltage Reference Permanent Fail
      20. 5.3.20 VSS Permanent Fail
      21. 5.3.21 Protection Comparator MUX Permanent Fail
      22. 5.3.22 Commanded Permanent Fail
      23. 5.3.23 Top of Stack Measurement Check
      24. 5.3.24 Cell Open Wire
7. 6 Device Status and Controls
   1. 6.1 0x00 Control Status() and 0x12 Battery Status() Commands
   2. 6.2 0x0070 MANU_DATA() Subcommand
   3. 6.3 LDOs
      1. 6.3.1 Preregulator Control
      2. 6.3.2 REG1 and REG2 LDO Controls
   4. 6.4 Multifunction Pin Controls
   5. 6.5 CFETOFF, DFETOFF, and BOTHOFF Pin Functionality
   6. 6.6 ALERT Pin Operation
   7. 6.7 DDSG and DCHG Pin Operation
   8. 6.8 Fuse Drive
   9. 6.9 Device Event Timing
8. 7 Operational Modes
   1. 7.1 Overview
   2. 7.2 NORMAL Mode
   3. 7.3 SLEEP Mode
   4. 7.4 DEEPSLEEP Mode
   5. 7.5 SHUTDOWN Mode
   6. 7.6 CONFIG_UPDATE Mode
9. 8 Device Security
   1. 8.1 Overview
10. 9 Serial Communications Interfaces
    1. 9.1 Serial Communications Overview
    2. 9.2 I2C Communications Subsystem
    3. 9.3 SPI Communications Interface
       1. 9.3.1 SPI Protocol
    4. 9.4 HDQ Communications Interface
11. 10Cell Balancing
    1. 10.1 Cell Balancing Operation
    2. 10.2 Cell Balancing Timing
12. 11Diagnostics
    1. 11.1 Diagnostics Overview
    2. 11.2 VREF2 Versus VREF1 Check
    3. 11.3 VSS Measurement
    4. 11.4 Top of Stack Measurement Check
    5. 11.5 LFO Oscillator Monitor
    6. 11.6 Protection Comparator Mux Check
    7. 11.7 Internal Watchdog Reset
    8. 11.8 Internal Memory Checks
13. 12Commands and Subcommands
    1. 12.1 Direct Commands
    2. 12.2 Bitfield Definitions for Direct Commands
       1. 12.2.1  Control Status Register
       2. 12.2.2  Safety Alert A Register
       3. 12.2.3  Safety Status A Register
       4. 12.2.4  Safety Alert B Register
       5. 12.2.5  Safety Status B Register
       6. 12.2.6  Safety Alert C Register
       7. 12.2.7  Safety Status C Register
       8. 12.2.8  PF Alert A Register
       9. 12.2.9  PF Status A Register
       10. 12.2.10 PF Alert B Register
       11. 12.2.11 PF Status B Register
       12. 12.2.12 PF Alert C Register
       13. 12.2.13 PF Status C Register
       14. 12.2.14 PF Alert D Register
       15. 12.2.15 PF Status D Register
       16. 12.2.16 Battery Status Register
       17. 12.2.17 Alarm Status Register
       18. 12.2.18 Alarm Raw Status Register
       19. 12.2.19 Alarm Enable Register
       20. 12.2.20 FET Status Register
    3. 12.3 Command-Only Subcommands
    4. 12.4 Subcommands with Data
    5. 12.5 Bitfield Definitions for Subcommands
       1. 12.5.1 PF Status A Register
       2. 12.5.2 PF Status B Register
       3. 12.5.3 PF Status C Register
       4. 12.5.4 PF Status D Register
       5. 12.5.5 Manufacturing Status Register
       6. 12.5.6 FET Control Register
       7. 12.5.7 REG12 Control Register
       8. 12.5.8 OTP Write Check Result Register
       9. 12.5.9 OTP Write Result Register
14. 13Data Memory Settings
    1. 13.1 Data Memory Access
    2. 13.2 Calibration
       1. 13.2.1  Calibration:Voltage
          1. 13.2.1.1  Calibration:Voltage:Cell 1 Gain
          2. 13.2.1.2  Calibration:Voltage:Cell 2 Gain
          3. 13.2.1.3  Calibration:Voltage:Cell 3 Gain
          4. 13.2.1.4  Calibration:Voltage:Cell 4 Gain
          5. 13.2.1.5  Calibration:Voltage:Cell 5 Gain
          6. 13.2.1.6  Calibration:Voltage:Cell 6 Gain
          7. 13.2.1.7  Calibration:Voltage:Cell 7 Gain
          8. 13.2.1.8  Calibration:Voltage:Cell 8 Gain
          9. 13.2.1.9  Calibration:Voltage:Cell 9 Gain
          10. 13.2.1.10 Calibration:Voltage:Cell 10 Gain
          11. 13.2.1.11 Calibration:Voltage:Cell 11 Gain
          12. 13.2.1.12 Calibration:Voltage:Cell 12 Gain
          13. 13.2.1.13 Calibration:Voltage:Cell 13 Gain
          14. 13.2.1.14 Calibration:Voltage:Cell 14 Gain
          15. 13.2.1.15 Calibration:Voltage:Pack Gain
          16. 13.2.1.16 Calibration:Voltage:TOS Gain
          17. 13.2.1.17 Calibration:Voltage:LD Gain
          18. 13.2.1.18 Calibration:Voltage:ADC Gain
       2. 13.2.2  Calibration:Current
          1. 13.2.2.1 Calibration:Current:CC Gain
          2. 13.2.2.2 Calibration:Current:Capacity Gain
       3. 13.2.3  Calibration:Vcell Offset
          1. 13.2.3.1 Calibration:Vcell Offset:Vcell Offset
       4. 13.2.4  Calibration:V Divider Offset
          1. 13.2.4.1 Calibration:V Divider Offset:Vdiv Offset
       5. 13.2.5  Calibration:Current Offset
          1. 13.2.5.1 Calibration:Current Offset:Coulomb Counter Offset Samples
          2. 13.2.5.2 Calibration:Current Offset:Board Offset
       6. 13.2.6  Calibration:Temperature
          1. 13.2.6.1  Calibration:Temperature:Internal Temp Offset
          2. 13.2.6.2  Calibration:Temperature:CFETOFF Temp Offset
          3. 13.2.6.3  Calibration:Temperature:DFETOFF Temp Offset
          4. 13.2.6.4  Calibration:Temperature:ALERT Temp Offset
          5. 13.2.6.5  Calibration:Temperature:TS1 Temp Offset
          6. 13.2.6.6  Calibration:Temperature:TS2 Temp Offset
          7. 13.2.6.7  Calibration:Temperature:TS3 Temp Offset
          8. 13.2.6.8  Calibration:Temperature:HDQ Temp Offset
          9. 13.2.6.9  Calibration:Temperature:DCHG Temp Offset
          10. 13.2.6.10 Calibration:Temperature:DDSG Temp Offset
       7. 13.2.7  Calibration:Internal Temp Model
          1. 13.2.7.1 Calibration:Internal Temp Model:Int Gain
          2. 13.2.7.2 Calibration:Internal Temp Model:Int base offset
          3. 13.2.7.3 Calibration:Internal Temp Model:Int Maximum AD
          4. 13.2.7.4 Calibration:Internal Temp Model:Int Maximum Temp
       8. 13.2.8  Calibration:18K Temperature Model
          1. 13.2.8.1  Calibration:18K Temperature Model:Coeff a1
          2. 13.2.8.2  Calibration:18K Temperature Model:Coeff a2
          3. 13.2.8.3  Calibration:18K Temperature Model:Coeff a3
          4. 13.2.8.4  Calibration:18K Temperature Model:Coeff a4
          5. 13.2.8.5  Calibration:18K Temperature Model:Coeff a5
          6. 13.2.8.6  Calibration:18K Temperature Model:Coeff b1
          7. 13.2.8.7  Calibration:18K Temperature Model:Coeff b2
          8. 13.2.8.8  Calibration:18K Temperature Model:Coeff b3
          9. 13.2.8.9  Calibration:18K Temperature Model:Coeff b4
          10. 13.2.8.10 Calibration:18K Temperature Model:Adc0
       9. 13.2.9  Calibration:180K Temperature Model
          1. 13.2.9.1  Calibration:180K Temperature Model:Coeff a1
          2. 13.2.9.2  Calibration:180K Temperature Model:Coeff a2
          3. 13.2.9.3  Calibration:180K Temperature Model:Coeff a3
          4. 13.2.9.4  Calibration:180K Temperature Model:Coeff a4
          5. 13.2.9.5  Calibration:180K Temperature Model:Coeff a5
          6. 13.2.9.6  Calibration:180K Temperature Model:Coeff b1
          7. 13.2.9.7  Calibration:180K Temperature Model:Coeff b2
          8. 13.2.9.8  Calibration:180K Temperature Model:Coeff b3
          9. 13.2.9.9  Calibration:180K Temperature Model:Coeff b4
          10. 13.2.9.10 Calibration:180K Temperature Model:Adc0
       10. 13.2.10 Calibration:Custom Temperature Model
           1. 13.2.10.1  Calibration:Custom Temperature Model:Coeff a1
           2. 13.2.10.2  Calibration:Custom Temperature Model:Coeff a2
           3. 13.2.10.3  Calibration:Custom Temperature Model:Coeff a3
           4. 13.2.10.4  Calibration:Custom Temperature Model:Coeff a4
           5. 13.2.10.5  Calibration:Custom Temperature Model:Coeff a5
           6. 13.2.10.6  Calibration:Custom Temperature Model:Coeff b1
           7. 13.2.10.7  Calibration:Custom Temperature Model:Coeff b2
           8. 13.2.10.8  Calibration:Custom Temperature Model:Coeff b3
           9. 13.2.10.9  Calibration:Custom Temperature Model:Coeff b4
           10. 13.2.10.10 Calibration:Custom Temperature Model:Rc0
           11. 13.2.10.11 Calibration:Custom Temperature Model:Adc0
       11. 13.2.11 Calibration:Current Deadband
           1. 13.2.11.1 Calibration:Current Deadband:Coulomb Counter Deadband
       12. 13.2.12 Calibration:CUV
           1. 13.2.12.1 Calibration:CUV:CUV Threshold Override
       13. 13.2.13 Calibration:COV
           1. 13.2.13.1 Calibration:COV:COV Threshold Override
    3. 13.3 Settings
       1. 13.3.1  Settings:Fuse
          1. 13.3.1.1 Settings:Fuse:Min Blow Fuse Voltage
          2. 13.3.1.2 Settings:Fuse:Fuse Blow Timeout
       2. 13.3.2  Settings:Configuration
          1. 13.3.2.1  Settings:Configuration:Power Config
          2. 13.3.2.2  Settings:Configuration:REG12 Config
          3. 13.3.2.3  Settings:Configuration:REG0 Config
          4. 13.3.2.4  Settings:Configuration:HWD Regulator Options
          5. 13.3.2.5  Settings:Configuration:Comm Type
          6. 13.3.2.6  Settings:Configuration:I2C Address
          7. 13.3.2.7  Settings:Configuration:SPI Configuration
          8. 13.3.2.8  Settings:Configuration:Comm Idle Time
          9. 13.3.2.9  Settings:Configuration:CFETOFF Pin Config
          10. 13.3.2.10 Settings:Configuration:DFETOFF Pin Config
          11. 13.3.2.11 Settings:Configuration:ALERT Pin Config
          12. 13.3.2.12 Settings:Configuration:TS1 Config
          13. 13.3.2.13 Settings:Configuration:TS2 Config
          14. 13.3.2.14 Settings:Configuration:TS3 Config
          15. 13.3.2.15 Settings:Configuration:HDQ Pin Config
          16. 13.3.2.16 Settings:Configuration:DCHG Pin Config
          17. 13.3.2.17 Settings:Configuration:DDSG Pin Config
          18. 13.3.2.18 Settings:Configuration:DA Configuration
          19. 13.3.2.19 Settings:Configuration:Vcell Mode
          20. 13.3.2.20 Settings:Configuration:CC3 Samples
       3. 13.3.3  Settings:Protection
          1. 13.3.3.1  Settings:Protection:Protection Configuration
          2. 13.3.3.2  Settings:Protection:Enabled Protections A
          3. 13.3.3.3  Settings:Protection:Enabled Protections B
          4. 13.3.3.4  Settings:Protection:Enabled Protections C
          5. 13.3.3.5  Settings:Protection:CHG FET Protections A
          6. 13.3.3.6  Settings:Protection:CHG FET Protections B
          7. 13.3.3.7  Settings:Protection:CHG FET Protections C
          8. 13.3.3.8  Settings:Protection:DSG FET Protections A
          9. 13.3.3.9  Settings:Protection:DSG FET Protections B
          10. 13.3.3.10 Settings:Protection:DSG FET Protections C
          11. 13.3.3.11 Settings:Protection:Body Diode Threshold
       4. 13.3.4  Settings:Alarm
          1. 13.3.4.1 Settings:Alarm:Default Alarm Mask
          2. 13.3.4.2 Settings:Alarm:SF Alert Mask A
          3. 13.3.4.3 Settings:Alarm:SF Alert Mask B
          4. 13.3.4.4 Settings:Alarm:SF Alert Mask C
          5. 13.3.4.5 Settings:Alarm:PF Alert Mask A
          6. 13.3.4.6 Settings:Alarm:PF Alert Mask B
          7. 13.3.4.7 Settings:Alarm:PF Alert Mask C
          8. 13.3.4.8 Settings:Alarm:PF Alert Mask D
       5. 13.3.5  Settings:Permanent Failure
          1. 13.3.5.1 Settings:Permanent Failure:Enabled PF A
          2. 13.3.5.2 Settings:Permanent Failure:Enabled PF B
          3. 13.3.5.3 Settings:Permanent Failure:Enabled PF C
          4. 13.3.5.4 Settings:Permanent Failure:Enabled PF D
       6. 13.3.6  Settings:FET
          1. 13.3.6.1 Settings:FET:FET Options
          2. 13.3.6.2 Settings:FET:Chg Pump Control
          3. 13.3.6.3 Settings:FET:Precharge Start Voltage
          4. 13.3.6.4 Settings:FET:Precharge Stop Voltage
          5. 13.3.6.5 Settings:FET:Predischarge Timeout
          6. 13.3.6.6 Settings:FET:Predischarge Stop Delta
       7. 13.3.7  Settings:Current Thresholds
          1. 13.3.7.1 Settings:Current Thresholds:Dsg Current Threshold
          2. 13.3.7.2 Settings:Current Thresholds:Chg Current Threshold
       8. 13.3.8  Settings:Cell Open-Wire
          1. 13.3.8.1 Settings:Cell Open-Wire:Check Time
       9. 13.3.9  Settings:Interconnect Resistances
          1. 13.3.9.1  Settings:Interconnect Resistances:Cell 1 Interconnect
          2. 13.3.9.2  Settings:Interconnect Resistances:Cell 2 Interconnect
          3. 13.3.9.3  Settings:Interconnect Resistances:Cell 3 Interconnect
          4. 13.3.9.4  Settings:Interconnect Resistances:Cell 4 Interconnect
          5. 13.3.9.5  Settings:Interconnect Resistances:Cell 5 Interconnect
          6. 13.3.9.6  Settings:Interconnect Resistances:Cell 6 Interconnect
          7. 13.3.9.7  Settings:Interconnect Resistances:Cell 7 Interconnect
          8. 13.3.9.8  Settings:Interconnect Resistances:Cell 8 Interconnect
          9. 13.3.9.9  Settings:Interconnect Resistances:Cell 9 Interconnect
          10. 13.3.9.10 Settings:Interconnect Resistances:Cell 10 Interconnect
          11. 13.3.9.11 Settings:Interconnect Resistances:Cell 11 Interconnect
          12. 13.3.9.12 Settings:Interconnect Resistances:Cell 12 Interconnect
          13. 13.3.9.13 Settings:Interconnect Resistances:Cell 13 Interconnect
          14. 13.3.9.14 Settings:Interconnect Resistances:Cell 14 Interconnect
       10. 13.3.10 Settings:Manufacturing
           1. 13.3.10.1 Settings:Manufacturing:Mfg Status Init
       11. 13.3.11 Settings:Cell Balancing Config
           1. 13.3.11.1  Settings:Cell Balancing Config:Balancing Configuration
           2. 13.3.11.2  Settings:Cell Balancing Config:Min Cell Temp
           3. 13.3.11.3  Settings:Cell Balancing Config:Max Cell Temp
           4. 13.3.11.4  Settings:Cell Balancing Config:Max Internal Temp
           5. 13.3.11.5  Settings:Cell Balancing Config:Cell Balance Interval
           6. 13.3.11.6  Settings:Cell Balancing Config:Cell Balance Max Cells
           7. 13.3.11.7  Settings:Cell Balancing Config:Cell Balance Min Cell V (Charge)
           8. 13.3.11.8  Settings:Cell Balancing Config:Cell Balance Min Delta (Charge)
           9. 13.3.11.9  Settings:Cell Balancing Config:Cell Balance Stop Delta (Charge)
           10. 13.3.11.10 Settings:Cell Balancing Config:Cell Balance Min Cell V (Relax)
           11. 13.3.11.11 Settings:Cell Balancing Config:Cell Balance Min Delta (Relax)
           12. 13.3.11.12 Settings:Cell Balancing Config:Cell Balance Stop Delta (Relax)
    4. 13.4 Power
       1. 13.4.1 Power:Shutdown
          1. 13.4.1.1 Power:Shutdown:Shutdown Cell Voltage
          2. 13.4.1.2 Power:Shutdown:Shutdown Stack Voltage
          3. 13.4.1.3 Power:Shutdown:Low V Shutdown Delay
          4. 13.4.1.4 Power:Shutdown:Shutdown Temperature
          5. 13.4.1.5 Power:Shutdown:Shutdown Temperature Delay
          6. 13.4.1.6 Power:Shutdown:FET Off Delay
          7. 13.4.1.7 Power:Shutdown:Shutdown Command Delay
          8. 13.4.1.8 Power:Shutdown:Auto Shutdown Time
          9. 13.4.1.9 Power:Shutdown:RAM Fail Shutdown Time
       2. 13.4.2 Power:Sleep
          1. 13.4.2.1 Power:Sleep:Sleep Current
          2. 13.4.2.2 Power:Sleep:Voltage Time
          3. 13.4.2.3 Power:Sleep:Wake Comparator Current
          4. 13.4.2.4 Power:Sleep:Sleep Hysteresis Time
          5. 13.4.2.5 Power:Sleep:Sleep Charger Voltage Threshold
          6. 13.4.2.6 Power:Sleep:Sleep Charger PACK-TOS Delta
    5. 13.5 System Data
       1. 13.5.1 System Data:Integrity
          1. 13.5.1.1 System Data:Integrity:Config RAM Signature
    6. 13.6 Protections
       1. 13.6.1  Protections:CUV
          1. 13.6.1.1 Protections:CUV:Threshold
          2. 13.6.1.2 Protections:CUV:Delay
          3. 13.6.1.3 Protections:CUV:Recovery Hysteresis
       2. 13.6.2  Protections:COV
          1. 13.6.2.1 Protections:COV:Threshold
          2. 13.6.2.2 Protections:COV:Delay
          3. 13.6.2.3 Protections:COV:Recovery Hysteresis
       3. 13.6.3  Protections:COVL
          1. 13.6.3.1 Protections:COVL:Latch Limit
          2. 13.6.3.2 Protections:COVL:Counter Dec Delay
          3. 13.6.3.3 Protections:COVL:Recovery Time
       4. 13.6.4  Protections:OCC
          1. 13.6.4.1 Protections:OCC:Threshold
          2. 13.6.4.2 Protections:OCC:Delay
          3. 13.6.4.3 Protections:OCC:Recovery Threshold
          4. 13.6.4.4 Protections:OCC:PACK-TOS Delta
       5. 13.6.5  Protections:OCD1
          1. 13.6.5.1 Protections:OCD1:Threshold
          2. 13.6.5.2 Protections:OCD1:Delay
       6. 13.6.6  Protections:OCD2
          1. 13.6.6.1 Protections:OCD2:Threshold
          2. 13.6.6.2 Protections:OCD2:Delay
       7. 13.6.7  Protections:SCD
          1. 13.6.7.1 Protections:SCD:Threshold
          2. 13.6.7.2 Protections:SCD:Delay
          3. 13.6.7.3 Protections:SCD:Recovery Time
       8. 13.6.8  Protections:OCD3
          1. 13.6.8.1 Protections:OCD3:Threshold
          2. 13.6.8.2 Protections:OCD3:Delay
       9. 13.6.9  Protections:OCD
          1. 13.6.9.1 Protections:OCD:Recovery Threshold
       10. 13.6.10 Protections:OCDL
           1. 13.6.10.1 Protections:OCDL:Latch Limit
           2. 13.6.10.2 Protections:OCDL:Counter Dec Delay
           3. 13.6.10.3 Protections:OCDL:Recovery Time
           4. 13.6.10.4 Protections:OCDL:Recovery Threshold
       11. 13.6.11 Protections:SCDL
           1. 13.6.11.1 Protections:SCDL:Latch Limit
           2. 13.6.11.2 Protections:SCDL:Counter Dec Delay
           3. 13.6.11.3 Protections:SCDL:Recovery Time
           4. 13.6.11.4 Protections:SCDL:Recovery Threshold
       12. 13.6.12 Protections:OTC
           1. 13.6.12.1 Protections:OTC:Threshold
           2. 13.6.12.2 Protections:OTC:Delay
           3. 13.6.12.3 Protections:OTC:Recovery
       13. 13.6.13 Protections:OTD
           1. 13.6.13.1 Protections:OTD:Threshold
           2. 13.6.13.2 Protections:OTD:Delay
           3. 13.6.13.3 Protections:OTD:Recovery
       14. 13.6.14 Protections:OTF
           1. 13.6.14.1 Protections:OTF:Threshold
           2. 13.6.14.2 Protections:OTF:Delay
           3. 13.6.14.3 Protections:OTF:Recovery
       15. 13.6.15 Protections:OTINT
           1. 13.6.15.1 Protections:OTINT:Threshold
           2. 13.6.15.2 Protections:OTINT:Delay
           3. 13.6.15.3 Protections:OTINT:Recovery
       16. 13.6.16 Protections:UTC
           1. 13.6.16.1 Protections:UTC:Threshold
           2. 13.6.16.2 Protections:UTC:Delay
           3. 13.6.16.3 Protections:UTC:Recovery
       17. 13.6.17 Protections:UTD
           1. 13.6.17.1 Protections:UTD:Threshold
           2. 13.6.17.2 Protections:UTD:Delay
           3. 13.6.17.3 Protections:UTD:Recovery
       18. 13.6.18 Protections:UTINT
           1. 13.6.18.1 Protections:UTINT:Threshold
           2. 13.6.18.2 Protections:UTINT:Delay
           3. 13.6.18.3 Protections:UTINT:Recovery
       19. 13.6.19 Protections:Recovery
           1. 13.6.19.1 Protections:Recovery:Time
       20. 13.6.20 Protections:HWD
           1. 13.6.20.1 Protections:HWD:Delay
       21. 13.6.21 Protections:Load Detect
           1. 13.6.21.1 Protections:Load Detect:Active Time
           2. 13.6.21.2 Protections:Load Detect:Retry Delay
           3. 13.6.21.3 Protections:Load Detect:Timeout
       22. 13.6.22 Protections:PTO
           1. 13.6.22.1 Protections:PTO:Charge Threshold
           2. 13.6.22.2 Protections:PTO:Delay
           3. 13.6.22.3 Protections:PTO:Reset
    7. 13.7 Permanent Fail
       1. 13.7.1  Permanent Fail:CUDEP
          1. 13.7.1.1 Permanent Fail:CUDEP:Threshold
          2. 13.7.1.2 Permanent Fail:CUDEP:Delay
       2. 13.7.2  Permanent Fail:SUV
          1. 13.7.2.1 Permanent Fail:SUV:Threshold
          2. 13.7.2.2 Permanent Fail:SUV:Delay
       3. 13.7.3  Permanent Fail:SOV
          1. 13.7.3.1 Permanent Fail:SOV:Threshold
          2. 13.7.3.2 Permanent Fail:SOV:Delay
       4. 13.7.4  Permanent Fail:TOS
          1. 13.7.4.1 Permanent Fail:TOS:Threshold
          2. 13.7.4.2 Permanent Fail:TOS:Delay
       5. 13.7.5  Permanent Fail:SOCC
          1. 13.7.5.1 Permanent Fail:SOCC:Threshold
          2. 13.7.5.2 Permanent Fail:SOCC:Delay
       6. 13.7.6  Permanent Fail:SOCD
          1. 13.7.6.1 Permanent Fail:SOCD:Threshold
          2. 13.7.6.2 Permanent Fail:SOCD:Delay
       7. 13.7.7  Permanent Fail:SOT
          1. 13.7.7.1 Permanent Fail:SOT:Threshold
          2. 13.7.7.2 Permanent Fail:SOT:Delay
       8. 13.7.8  Permanent Fail:SOTF
          1. 13.7.8.1 Permanent Fail:SOTF:Threshold
          2. 13.7.8.2 Permanent Fail:SOTF:Delay
       9. 13.7.9  Permanent Fail:VIMR
          1. 13.7.9.1 Permanent Fail:VIMR:Check Voltage
          2. 13.7.9.2 Permanent Fail:VIMR:Max Relax Current
          3. 13.7.9.3 Permanent Fail:VIMR:Threshold
          4. 13.7.9.4 Permanent Fail:VIMR:Delay
          5. 13.7.9.5 Permanent Fail:VIMR:Relax Min Duration
       10. 13.7.10 Permanent Fail:VIMA
           1. 13.7.10.1 Permanent Fail:VIMA:Check Voltage
           2. 13.7.10.2 Permanent Fail:VIMA:Min Active Current
           3. 13.7.10.3 Permanent Fail:VIMA:Threshold
           4. 13.7.10.4 Permanent Fail:VIMA:Delay
       11. 13.7.11 Permanent Fail:CFETF
           1. 13.7.11.1 Permanent Fail:CFETF:OFF Threshold
           2. 13.7.11.2 Permanent Fail:CFETF:OFF Delay
       12. 13.7.12 Permanent Fail:DFETF
           1. 13.7.12.1 Permanent Fail:DFETF:OFF Threshold
           2. 13.7.12.2 Permanent Fail:DFETF:OFF Delay
       13. 13.7.13 Permanent Fail:VSSF
           1. 13.7.13.1 Permanent Fail:VSSF:Fail Threshold
           2. 13.7.13.2 Permanent Fail:VSSF:Delay
       14. 13.7.14 Permanent Fail:2LVL
           1. 13.7.14.1 Permanent Fail:2LVL:Delay
       15. 13.7.15 Permanent Fail:LFOF
           1. 13.7.15.1 Permanent Fail:LFOF:Delay
       16. 13.7.16 Permanent Fail:HWMX
           1. 13.7.16.1 Permanent Fail:HWMX:Delay
    8. 13.8 Security
       1. 13.8.1 Security:Settings
          1. 13.8.1.1 Security:Settings:Security Settings
       2. 13.8.2 Security:Keys
          1. 13.8.2.1 Security:Keys:Unseal Key Step 1
          2. 13.8.2.2 Security:Keys:Unseal Key Step 2
          3. 13.8.2.3 Security:Keys:Full Access Key Step 1
          4. 13.8.2.4 Security:Keys:Full Access Key Step 2
    9. 13.9 Data Memory Summary
15. 15Revision History