米6体育平台手机版

SLUUCJ0 November 2023 BQ76907

11.1 Direct Commands

Direct Commands Table

Command	Name	Units	Type	Access	Description
0x02	Safety Alert A	Hex	H1	Sealed: R Full Access: R	Provides individual alert signals when enabled safety alerts have triggered. Bit descriptions can be found in Safety Alert A Register.
0x03	Safety Status A	Hex	H1	Sealed: R Full Access: R	Provides individual fault signals when enabled safety faults have triggered. Bit descriptions can be found in Safety Status A Register.
0x04	Safety Alert B	Hex	H1	Sealed: R Full Access: R	Provides individual alert signals when enabled safety alerts have triggered. Bit descriptions can be found in Safety Alert B Register.
0x05	Safety Status B	Hex	H1	Sealed: R Full Access: R	Provides individual fault signals when enabled safety faults have triggered. Bit descriptions can be found in Safety Status B Register.
0x12	Battery Status	Hex	H2	Sealed: R Full Access: R	Provides flags related to battery status. Bit descriptions can be found in Battery Status Register.
0x14	Cell 1 Voltage	mV	I2	Sealed: R Full Access: R	16-bit voltage on cell 1.
0x16	Cell 2 Voltage	mV	I2	Sealed: R Full Access: R	16-bit voltage on cell 2.
0x18	Cell 3 Voltage	mV	I2	Sealed: R Full Access: R	16-bit voltage on cell 3.
0x1A	Cell 4 Voltage	mV	I2	Sealed: R Full Access: R	16-bit voltage on cell 4.
0x1C	Cell 5 Voltage	mV	I2	Sealed: R Full Access: R	16-bit voltage on cell 5.
0x1E	Cell 6 Voltage	mV	I2	Sealed: R Full Access: R	16-bit voltage on cell 6.
0x20	Cell 7 Voltage	mV	I2	Sealed: R Full Access: R	16-bit voltage on cell 7.
0x22	REG18 Voltage	16-bit ADC codes	I2	Sealed: R Full Access: R	Internal 1.8V regulator voltage measured using bandgap reference, used for diagnostic of VREF1 vs VREF2.
0x24	VSS Voltage	16-bit ADC codes	I2	Sealed: R Full Access: R	Measurement of VSS using ADC, used for diagnostic of ADC input mux
0x26	Stack Voltage	mV	U2	Sealed: R Full Access: R	16-bit voltage on top of stack
0x28	Int Temperature	ºC	I2	Sealed: R Full Access: R	This is the most recent measured internal die temperature.
0x2A	TS Measurement	16-bit ADC codes	I2	Sealed: R Full Access: R	ADC measurement of the TS pin.
0x36	Raw Current	24-bit ADC codes sign-extended for 32-bit format	I4	Sealed: R Full Access: R	32-bit raw current measurement
0x3A	Current	userA	I2	Sealed: R Full Access: R	16-bit CC2 current measurement
0x3C	CC1 Current	userA	I2	Sealed: R Full Access: R	16-bit CC1 current measurement
0x62	Alarm Status	Hex	H2	Sealed: R/W Full Access: R/W	Latched signal used to assert the ALERT pin. Write a bit high to clear the latched bit. Bit descriptions can be found in Alarm Status Register.
0x64	Alarm Raw Status	Hex	H2	Sealed: R Full Access: R	Unlatched value of flags which can be selected to be latched (using Alarm Enable()) and used to assert the ALERT pin. Bit descriptions can be found in Alarm Raw Status Register.
0x66	Alarm Enable	Hex	H2	Sealed: R/W Full Access: R/W	Mask for Alarm Status(). Can be written to change during operation to change which alarm sources are enabled. The default value of this parameter is set by Settings:Configuration:Default Alarm Mask. Bit descriptions can be found in Alarm Enable Register.
0x68	FET CONTROL	Hex	H1	Sealed: R/W Full Access: R/W	FET Control: Allows host control of individual FET drivers. Bit descriptions can be found in FET CONTROL Register.
0x69	REGOUT CONTROL	Hex	H1	Sealed: R/W Full Access: R/W	REGOUT Control: Changes voltage regulator settings. Bit descriptions can be found in REGOUT CONTROL Register.
0x6A	DSG FET Driver PWM Control	Hex	H2	Sealed: R/W Full Access: R/W	Controls the PWM mode of the DSG FET driver. Values are not used until the second byte is written. Bit descriptions can be found in DSG FET Driver PWM Control Register.
0x6C	CHG FET Driver PWM Control	Hex	H2	Sealed: R/W Full Access: R/W	Controls the PWM mode of the CHG FET driver. Values are not used until the second byte is written. Bit descriptions can be found in CHG FET Driver PWM Control Register.