SNAS605AS March   2013  – May 2020 LMK04821 , LMK04826 , LMK04828

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
    1.     Simplified Schematic
  4. 4 Revision History
  5. 5 Device Comparison Table
    1. 5.1 Device Configuration Information
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 SPI Interface Timing
    7. 7.7 Typical Characteristics – Clock Output AC Characteristics
  8. 8 Parameter Measurement Information
    1. 8.1 Charge Pump Current Specification Definitions
      1. 8.1.1 Charge Pump Output Current Magnitude Variation Vs. Charge Pump Output Voltage
      2. 8.1.2 Charge Pump Sink Current Vs. Charge Pump Output Source Current Mismatch
      3. 8.1.3 Charge Pump Output Current Magnitude Variation Vs. Ambient Temperature
    2. 8.2 Differential Voltage Measurement Terminology
  9. 9 Detailed Description
    1. 9.1 Overview
      1. 9.1.1  Jitter Cleaning
      2. 9.1.2  JEDEC JESD204B Support
      3. 9.1.3  Three PLL1 Redundant Reference Inputs
      4. 9.1.4  VCXO/Crystal Buffered Output
      5. 9.1.5  Frequency Holdover
      6. 9.1.6  PLL2 Integrated Loop Filter Poles
      7. 9.1.7  Internal VCOs
        1. 9.1.7.1 VCO1 Divider (LMK04821 only)
      8. 9.1.8  External VCO Mode
      9. 9.1.9  Clock Distribution
        1. 9.1.9.1 Device Clock Divider
        2. 9.1.9.2 SYSREF Clock Divider
        3. 9.1.9.3 Device Clock Delay
        4. 9.1.9.4 SYSREF Delay
        5. 9.1.9.5 Glitchless Half Step and Glitchless Analog Delay
        6. 9.1.9.6 Programmable Output Formats
        7. 9.1.9.7 Clock Output Synchronization
      10. 9.1.10 Zero-Delay
      11. 9.1.11 Status Pins
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 SYNC/SYSREF
      2. 9.3.2 JEDEC JESD204B
        1. 9.3.2.1 How To Enable SYSREF
          1. 9.3.2.1.1 Setup of SYSREF Example
          2. 9.3.2.1.2 SYSREF_CLR
        2. 9.3.2.2 SYSREF Modes
          1. 9.3.2.2.1 SYSREF Pulser
          2. 9.3.2.2.2 Continuous SYSREF
          3. 9.3.2.2.3 SYSREF Request
      3. 9.3.3 Digital Delay
        1. 9.3.3.1 Fixed Digital Delay
          1. 9.3.3.1.1 Fixed Digital Delay Example
        2. 9.3.3.2 Dynamic Digital Delay
        3. 9.3.3.3 Single and Multiple Dynamic Digital Delay Example
      4. 9.3.4 SYSREF to Device Clock Alignment
      5. 9.3.5 Input Clock Switching
        1. 9.3.5.1 Input Clock Switching - Manual Mode
        2. 9.3.5.2 Input Clock Switching - Pin Select Mode
        3. 9.3.5.3 Input Clock Switching - Automatic Mode
      6. 9.3.6 Digital Lock Detect
      7. 9.3.7 Holdover
        1. 9.3.7.1 Enable Holdover
          1. 9.3.7.1.1 Fixed (Manual) CPout1 Holdover Mode
          2. 9.3.7.1.2 Tracked CPout1 Holdover Mode
        2. 9.3.7.2 Entering Holdover
        3. 9.3.7.3 During Holdover
        4. 9.3.7.4 Exiting Holdover
        5. 9.3.7.5 Holdover Frequency Accuracy and DAC Performance
        6. 9.3.7.6 Holdover Mode - Automatic Exit of Holdover
    4. 9.4 Device Functional Modes
      1. 9.4.1 Dual PLL
      2. 9.4.2 Zero-Delay Dual PLL
      3. 9.4.3 Single-Loop Mode
      4. 9.4.4 Single-Loop Mode With External VCO
      5. 9.4.5 Distribution Mode
    5. 9.5 Programming
      1. 9.5.1 Recommended Programming Sequence
        1. 9.5.1.1 SPI LOCK
        2. 9.5.1.2 SYSREF_CLR
        3. 9.5.1.3 RESET Pin
    6. 9.6 Register Maps
      1. 9.6.1 Register Map for Device Programming
    7. 9.7 Device Register Descriptions
      1. 9.7.1 System Functions
        1. 9.7.1.1 RESET, SPI_3WIRE_DIS
        2. 9.7.1.2 POWERDOWN
        3. 9.7.1.3 ID_DEVICE_TYPE
        4. 9.7.1.4 ID_PROD[15:8], ID_PROD
        5. 9.7.1.5 ID_MASKREV
        6. 9.7.1.6 ID_VNDR[15:8], ID_VNDR
      2. 9.7.2 (0x100 - 0x138) Device Clock and SYSREF Clock Output Controls
        1. 9.7.2.1 CLKoutX_Y_ODL, CLKoutX_Y_IDL, DCLKoutX_DIV
        2. 9.7.2.2 DCLKoutX_DDLY_CNTH, DCLKoutX_DDLY_CNTL
        3. 9.7.2.3 DCLKoutX_ADLY, DCLKoutX_ADLY_MUX, DCLKout_MUX
        4. 9.7.2.4 DCLKoutX_HS, SDCLKoutY_MUX, SDCLKoutY_DDLY, SDCLKoutY_HS
        5. 9.7.2.5 SDCLKoutY_ADLY_EN, SDCLKoutY_ADLY
        6. 9.7.2.6 DCLKoutX_DDLY_PD, DCLKoutX_HSg_PD, DCLKout_ADLYg_PD, DCLKout_ADLY_PD, DCLKoutX_Y_PD, SDCLKoutY_DIS_MODE, SDCLKoutY_PD
        7. 9.7.2.7 SDCLKoutY_POL, SDCLKoutY_FMT, DCLKoutX_POL, DCLKoutX_FMT
      3. 9.7.3 SYSREF, SYNC, and Device Config
        1. 9.7.3.1  VCO_MUX, OSCout_MUX, OSCout_FMT
        2. 9.7.3.2  SYSREF_CLKin0_MUX, SYSREF_MUX
        3. 9.7.3.3  SYSREF_DIV[12:8], SYSREF_DIV[7:0]
        4. 9.7.3.4  SYSREF_DDLY[12:8], SYSREF_DDLY[7:0]
        5. 9.7.3.5  SYSREF_PULSE_CNT
        6. 9.7.3.6  PLL2_NCLK_MUX, PLL1_NCLK_MUX, FB_MUX, FB_MUX_EN
        7. 9.7.3.7  PLL1_PD, VCO_LDO_PD, VCO_PD, OSCin_PD, SYSREF_GBL_PD, SYSREF_PD, SYSREF_DDLY_PD, SYSREF_PLSR_PD
        8. 9.7.3.8  DDLYdSYSREF_EN, DDLYdX_EN
        9. 9.7.3.9  DDLYd_STEP_CNT
        10. 9.7.3.10 SYSREF_CLR, SYNC_1SHOT_EN, SYNC_POL, SYNC_EN, SYNC_PLL2_DLD, SYNC_PLL1_DLD, SYNC_MODE
        11. 9.7.3.11 SYNC_DISSYSREF, SYNC_DISX
        12. 9.7.3.12 Fixed Registers (0x145, 0x171 - 0x172)
      4. 9.7.4 (0x146 - 0x149) CLKin Control
        1. 9.7.4.1 CLKin2_EN, CLKin1_EN, CLKin0_EN, CLKin2_TYPE, CLKin1_TYPE, CLKin0_TYPE
        2. 9.7.4.2 CLKin_SEL_POL, CLKin_SEL_MODE, CLKin1_OUT_MUX, CLKin0_OUT_MUX
        3. 9.7.4.3 CLKin_SEL0_MUX, CLKin_SEL0_TYPE
        4. 9.7.4.4 SDIO_RDBK_TYPE, CLKin_SEL1_MUX, CLKin_SEL1_TYPE
      5. 9.7.5 RESET_MUX, RESET_TYPE
      6. 9.7.6 (0x14B - 0x152) Holdover
        1. 9.7.6.1 LOS_TIMEOUT, LOS_EN, TRACK_EN, HOLDOVER_FORCE, MAN_DAC_EN, MAN_DAC[9:8]
        2. 9.7.6.2 MAN_DAC[9:8], MAN_DAC[7:0]
        3. 9.7.6.3 DAC_TRIP_LOW
        4. 9.7.6.4 DAC_CLK_MULT, DAC_TRIP_HIGH
        5. 9.7.6.5 DAC_CLK_CNTR
        6. 9.7.6.6 CLKin_OVERRIDE, HOLDOVER_PLL1_DET, HOLDOVER_LOS_DET, HOLDOVER_VTUNE_DET, HOLDOVER_HITLESS_SWITCH, HOLDOVER_EN
        7. 9.7.6.7 HOLDOVER_DLD_CNT[13:8], HOLDOVER_DLD_CNT[7:0]
      7. 9.7.7 (0x153 - 0x15F) PLL1 Configuration
        1. 9.7.7.1 CLKin0_R[13:8], CLKin0_R[7:0]
        2. 9.7.7.2 CLKin1_R[13:8], CLKin1_R[7:0]
        3. 9.7.7.3 CLKin2_R[13:8], CLKin2_R[7:0]
        4. 9.7.7.4 PLL1_N
        5. 9.7.7.5 PLL1_WND_SIZE, PLL1_CP_TRI, PLL1_CP_POL, PLL1_CP_GAIN
        6. 9.7.7.6 PLL1_DLD_CNT[13:8], PLL1_DLD_CNT[7:0]
        7. 9.7.7.7 PLL1_R_DLY, PLL1_N_DLY
        8. 9.7.7.8 PLL1_LD_MUX, PLL1_LD_TYPE
      8. 9.7.8 (0x160 - 0x16E) PLL2 Configuration
        1. 9.7.8.1 PLL2_R[11:8], PLL2_R[7:0]
        2. 9.7.8.2 PLL2_P, OSCin_FREQ, PLL2_XTAL_EN, PLL2_REF_2X_EN
        3. 9.7.8.3 PLL2_N_CAL
        4. 9.7.8.4 PLL2_FCAL_DIS, PLL2_N
        5. 9.7.8.5 PLL2_WND_SIZE, PLL2_CP_GAIN, PLL2_CP_POL, PLL2_CP_TRI
        6. 9.7.8.6 SYSREF_REQ_EN, PLL2_DLD_CNT
        7. 9.7.8.7 PLL2_LF_R4, PLL2_LF_R3
        8. 9.7.8.8 PLL2_LF_C4, PLL2_LF_C3
        9. 9.7.8.9 PLL2_LD_MUX, PLL2_LD_TYPE
      9. 9.7.9 (0x16F - 0x1FFF) Misc Registers
        1. 9.7.9.1  PLL2_PRE_PD, PLL2_PD
        2. 9.7.9.2  VCO1_DIV
        3. 9.7.9.3  OPT_REG_1
        4. 9.7.9.4  OPT_REG_2
        5. 9.7.9.5  RB_PLL1_LD_LOST, RB_PLL1_LD, CLR_PLL1_LD_LOST
        6. 9.7.9.6  RB_PLL2_LD_LOST, RB_PLL2_LD, CLR_PLL2_LD_LOST
        7. 9.7.9.7  RB_DAC_VALUE(MSB), RB_CLKinX_SEL, RB_CLKinX_LOS
        8. 9.7.9.8  RB_DAC_VALUE
        9. 9.7.9.9  RB_HOLDOVER
        10. 9.7.9.10 SPI_LOCK
  10. 10Applications and Implementation
    1. 10.1 Application Information
    2. 10.2 Digital Lock Detect Frequency Accuracy
      1. 10.2.1 Minimum Lock Time Calculation Example
    3. 10.3 Driving CLKin and OSCin Inputs
      1. 10.3.1 Driving CLKin and OSCin Pins With a Differential Source
      2. 10.3.2 Driving CLKin and OSCin Pins With a Single-Ended Source
    4. 10.4 Output Termination and Biasing
      1. 10.4.1 LVPECL
      2. 10.4.2 LVDS/HSDS
    5. 10.5 Typical Applications
      1. 10.5.1 Design Example
        1. 10.5.1.1 Design Requirements
        2. 10.5.1.2 Detailed Design Procedure
          1. 10.5.1.2.1 Device Configuration and Simulation - PLLatinum Sim
          2. 10.5.1.2.2 Device Programming
        3. 10.5.1.3 Application Curves
    6. 10.6 System Examples
      1. 10.6.1 System Level Diagram
    7. 10.7 Do's and Don'ts
  11. 11Power Supply Recommendations
    1. 11.1 Pin Connection Recommendations
      1. 11.1.1 VCC Pins and Decoupling
        1. 11.1.1.1 Clock Output Supplies
        2. 11.1.1.2 Low-Crosstalk Supplies
        3. 11.1.1.3 PLL2 Supplies
        4. 11.1.1.4 Clock Input Supplies
        5. 11.1.1.5 Unused Clock Inputs/Outputs
    2. 11.2 Current Consumption / Power Dissipation Calculations
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Thermal Management
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Development Support
        1. 13.1.1.1 PLLatinum Sim
        2. 13.1.1.2 TICS Pro
    2. 13.2 Related Links
    3. 13.3 Trademarks
    4. 13.4 Electrostatic Discharge Caution
    5. 13.5 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

11.2 Current Consumption / Power Dissipation Calculations

From Table 87, the current consumption can be calculated for any configuration. The data below is typical and not assured.

The TICS Pro device profiles for LMK0482x family devices also include a current calculator, which performs real-time analysis of the register settings and estimates the current consumption based on which blocks are enabled. TI strongly recommends using TICS Pro to compute the current for any device profile, as it is faster and more flexible than manual computation using the table below. TICS Pro does not require a connection to the LMK0482x to generate a current consumption estimate or a register file.

Table 87. Typical Current Consumption for Selected Functional Blocks
(TA = 25 °C, VCC = 3.3 V)

BLOCK CONDITION TYPICAL ICC
(mA)		 POWER
DISSIPATED
in DEVICE
(mW)
CORE and FUNCTIONAL BLOCKS
Core Dual loop, internal VCO0 PLL1 and PLL2 locked 131.5 433.95
VCO (with VCO divider for LMK04821) VCO1 is selected LMK04826/LMK04828 13.5 44.55
LMK04821 22 72.6
OSCin Doubler Doubler is enabled EN_PLL2_REF_2X = 1 3 9.9
CLKin Any one of the CLKinX is enabled 4.9 16.17
Holdover Holdover is enabled HOLDOVER_EN = 1 1.3 4.29
Hitless switch is enabled HOLDOVER_HITLESS_SWITCH = 1 0.9 2.97
Track mode TRACK_EN = 1 2.5 8.25
SYNC_EN = 1 Required for SYNC and SYSREF functionality 7.6 25.08
SYSREF Enabled SYSREF_PD = 0 27.2 89.76
Dynamic digital delay enabled SYSREF_DDLY_PD = 0 5 16.5
Pulser is enabled SYSREF_PLSR_PD = 0 4.1 13.53
SYSREF pulses mode SYSREF_MUX = 2 3 9.9
SYSREF continuous mode SYSREF_MUX = 3 3 9.9
CLOCK GROUP
Enabled Any one of the CLKoutX_Y_PD = 0 20.1 66.33
IDL Any one of the CLKoutX_Y_IDL = 1 2.2 7.26
ODL Andy one of the CLKoutX_Y_ODL = 1 3.2 10.56
Clock Divider Divider only DCLKoutX_MUX = 0 13.6 44.88
Divider + DCC + HS DCLKoutX_MUX = 1 17.7 58.41
Analog delay + divider DCLKoutX_MUX = 3 13.6 44.88
CLOCK OUTPUT BUFFERS
LVDS 100-Ω differential termination 6 19.8
HSDS HSDS 6 mA, 100-Ω differential termination 8.8 29.04
HSDS 8 mA, 100-Ω differential termination 11.6 38.28
HSDS 10 mA, 100-Ω differential termination 19.4 64.02
OSCout BUFFERS
LVDS 100-Ω differential termination 18.5 61.05
LVCMOS LVCMOS pair 150 MHz 42.6 140.58
LVCMOS single 150 MHz 27 89.1
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |