SNVS871M July   2012  – June 2020

PRODUCTION DATA.  

1. 1 Features
2. 2 Applications
   1.     Simplified Schematic
3. 3 Description
4. 4 Revision History
5. 5 Device Options
6. 6 Pin Configuration and Functions
   1.     Pin Functions
7. 7 Specifications
   1. 7.1  Absolute Maximum Ratings
   2. 7.2  ESD Ratings
   3. 7.3  Recommended Operating Conditions
   4. 7.4  Thermal Information
   5. 7.5  Electrical Characteristics
   6. 7.6  Electrical Characteristics — Boost Converter
   7. 7.7  Electrical Characteristics — LED Driver
   8. 7.8  Electrical Characteristics — PWM Interface
   9. 7.9  Electrical Characteristics — Logic Interface
   10. 7.10 I2C Serial Bus Timing Parameters (SDA, SCL)
   11. 7.11 Typical Characteristics
8. 8 Detailed Description
   1. 8.1 Overview
   2. 8.2 Functional Block Diagram
   3. 8.3 Feature Description
      1. 8.3.1 Boost Converter
         1. 8.3.1.1 Boost Converter Operation
         2. 8.3.1.2 Setting Boost Switching Frequency
         3. 8.3.1.3 Output Voltage Control
            1. 8.3.1.3.1 Adaptive Control
            2. 8.3.1.3.2 Manual Control
         4. 8.3.1.4 EMI Reduction
      2. 8.3.2 Brightness Control
         1. 8.3.2.1  BRT_MODE = 00
         2. 8.3.2.2  BRT_MODE = 01
         3. 8.3.2.3  BRT_MODE = 10
         4. 8.3.2.4  BRT_MODE = 11
         5. 8.3.2.5  Output Dimming Schemes
            1. 8.3.2.5.1 PWM Control
            2. 8.3.2.5.2 Pure Current Control
            3. 8.3.2.5.3 Adaptive Control
         6. 8.3.2.6  Setting Full-Scale LED Current
         7. 8.3.2.7  Setting PWM Dimming Frequency
         8. 8.3.2.8  Phase Shift PWM Scheme
         9. 8.3.2.9  Slope and Advanced Slope
         10. 8.3.2.10 Dithering
      3. 8.3.3 Fault Detection
         1. 8.3.3.1 LED Fault Detection
            1. 8.3.3.1.1 Open Detect
            2. 8.3.3.1.2 Short Detect
         2. 8.3.3.2 Undervoltage Detection
         3. 8.3.3.3 Overcurrent Protection
         4. 8.3.3.4 Thermal Shutdown
   4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Active Mode
   5. 8.5 Programming
      1. 8.5.1 I2C-Compatible Serial Bus Interface
         1. 8.5.1.1 Interface Bus Overview
         2. 8.5.1.2 Data Transactions
         3. 8.5.1.3 Acknowledge Cycle
         4. 8.5.1.4 Acknowledge After Every Byte Rule
         5. 8.5.1.5 Addressing Transfer Formats
         6. 8.5.1.6 Control Register Write Cycle
         7. 8.5.1.7 Control Register Read Cycle
         8. 8.5.1.8 Register Read and Write Detail
   6. 8.6 Register Maps
      1. 8.6.1 Register Bit Explanations
         1. 8.6.1.1 Brightness Control
         2. 8.6.1.2 Device Control
         3. 8.6.1.3 Status
         4. 8.6.1.4 Direct Control
         5. 8.6.1.5 LED String Enable
      2. 8.6.2 EPROM Bit Explanations
         1. 8.6.2.1  LP8556TM (DSBGA) Configurations and Pre-Configured EPROM Settings
         2. 8.6.2.2  LP8556TM (DSBGA) Configurations and Pre-configured EPROM Settings Continued
         3. 8.6.2.3  LP8556SQ (WQFN) Configurations and Pre-configured EPROM Settings
         4. 8.6.2.4  CFG98
         5. 8.6.2.5  CFG9E
         6. 8.6.2.6  CFG0
         7. 8.6.2.7  CFG1
         8. 8.6.2.8  CFG2
         9. 8.6.2.9  CFG3
         10. 8.6.2.10 CFG4
         11. 8.6.2.11 CFG5
         12. 8.6.2.12 CFG6
         13. 8.6.2.13 CFG7
         14. 8.6.2.14 CFG9
         15. 8.6.2.15 CFGA
         16. 8.6.2.16 CFGE
         17. 8.6.2.17 CFGF
9. 9 Application and Implementation
   1. 9.1 Application Information
      1. 9.1.1 Using LP8556 With I2C Host
         1. 9.1.1.1 Setting Boost Switching and PWM Dimming Frequencies
         2. 9.1.1.2 Setting Full-Scale LED Current
      2. 9.1.2 Using LP8556 With Configuration Resistors and IO Pins
         1. 9.1.2.1 Setting Boost Switching and PWM Dimming Frequencies
         2. 9.1.2.2 Setting Full-Scale LED Current
   2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
         1. 9.2.2.1 Recommended Inductance for the Boost Power Stage
         2. 9.2.2.2 Recommended Capacitances for the Boost and LDO Power Stages
      3. 9.2.3 Application Curves
10. 10Power Supply Recommendations
11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Examples
12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Community Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
13. 13Mechanical, Packaging, and Orderable Information