SPRUJF1 November   2024 AM2612

ADVANCE INFORMATION  

  1.   1
  2.   Description
  3.   Key Features
  4. 1LaunchPad Module Overview
    1. 2.1 Introduction
    2. 2.2 Preface: Read This First
      1. 2.2.1 If You Need Assistance
      2. 2.2.2 Important Usage Notes
    3. 2.3 Kit Contents
    4. 2.4 Device Information
      1. 2.4.1 System Architecture Overview
      2. 2.4.2 Security
      3. 2.4.3 Compliance
      4. 2.4.4 BoosterPacks
      5. 2.4.5 Component Identification
  5. 2Hardware Description
    1. 3.1  Board Setup
      1. 3.1.1 Power Requirements
        1. 3.1.1.1 Power Input Using USB Type-C Connector
        2. 3.1.1.2 Power Status LEDs
        3. 3.1.1.3 Power Tree
      2. 3.1.2 Push Buttons
      3. 3.1.3 Boot mode Selection
      4. 3.1.4 IO Expander
    2. 3.2  Functional Block Diagram
    3. 3.3  GPIO Mapping
    4. 3.4  Reset
    5. 3.5  Clock
    6. 3.6  Memory Interfaces
      1. 3.6.1 OSPI
      2. 3.6.2 Board ID EEPROM
    7. 3.7  Ethernet Interface
      1. 3.7.1 Ethernet PHY Add-on Board connector #0 - CPSW RGMII/ICSSM
      2. 3.7.2 Ethernet PHY Add-on Board connector #1 - CPSW RGMII/ICSSM
    8. 3.8  I2C
    9. 3.9  Industrial Application LEDs
    10. 3.10 SPI
    11. 3.11 UART
    12. 3.12 MCAN
    13. 3.13 FSI
    14. 3.14 JTAG
    15. 3.15 TIVA and Test Automation Pin Mapping
    16. 3.16 LIN
    17. 3.17 ADC and DAC
    18. 3.18 EQEP and SDFM
    19. 3.19 EPWM
    20. 3.20 USB
    21. 3.21 BoosterPack Headers
  6. 3Known Issues and modifications done on LP-AM261 RevE1
    1. 4.1 TA_POWERDOWNz pulled up by VSYS_TA_3V3 which is powered by VSYS_3V3
    2. 4.2 USB2.0_MUX_SEL0 pulled up by R355
    3. 4.3 MDIO and MDC of PRU0-ICSS0 needs to be routed to both Ethernet PHYs
    4. 4.4 AM261_RGMII1_RXLINK and AM261_RGMII2_RXLINK to be connected to GPIO
  7. 4Additional Information
    1.     Trademarks
    2. 5.1 Sitara MCU+ Academy
  8. 5References
    1. 6.1 Reference Documents
    2. 6.2 Other TI Components Used in This Design
    3. 6.3 Related Documentation From Texas Instruments
  9. 6Revision History

2.20 USB

The USB interface of AM261x is routed to the USB2.0 Micro_AB Port and USB Type C port on the AM261x LaunchPad. USB signals from the connector routed to one of the ports of a 2:1 mux and the other port contains signals coming from the Type C power input, an IO expander is used to select between them.

AM261x supports USB DFU Bootmode. Boot mode selection and details are given in Bootmode

AM261x USB ConnectionFigure 2-28 USB Connection
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |