米6体育平台手机版

SWRU580 April 2021 CC2564C , CC2564MODA , CC2564MODN

Trademarks
1 Introduction
2 A2DP (AUD) Demo Guide
1. 2.1 Demo Overview
2. 2.2 Demo Application
3. 2.3 Application Commands
3 A3DP Sink Demo Guide
1. 3.1 Demo Overview
2. 3.2 Demo Application
3. 3.3 Sink Reference Board Demo Application
4. 3.4 Multiple Source Demo
5. 3.5 Application Commands
4 A3DP Source Demo Guide
1. 4.1 Demo Overview
2. 4.2 Demo Application
3. 4.3 Application Commands
5 HFP Demo Guide
1. 5.1 Demo Overview
2. 5.2 Demo Application
3. 5.3 Application Commands
6 HFP Audio Gateway Demo Guide
1. 6.1 Demo Overview
2. 6.2 Demo Application
3. 6.3 Application Commands
7 HID Demo Guide
1. 7.1 Demo Overview
2. 7.2 Demo Application
3. 7.3 Application Commands
8 HSP Demo Guide
1. 8.1 Demo Overview
2. 8.2 Demo Application
3. 8.3 Application Command
9 Map Demo Guide
1. 9.1 Demo Overview
2. 9.2 Demo Application
3. 9.3 Application Command
10PBAP Demo Guide
1. 10.1 Demo Overview
2. 10.2 Demo Application
3. 10.3 Application Commands
11SPP Demo Guide
1. 11.1 Demo Overview
2. 11.2 Demo Application
3. 11.3 Application Commands
12SPPLE Demo Guide
1. 12.1 Demo Overview
2. 12.2 Demo Application
3. 12.3 Demonstrating SPP LE on an iOS Device with the LightBlue App
4. 12.4 Demonstrating SPP LE on an iOS Device with the SPPLE Transfer App - LEGACY
5. 12.5 SPP Demo
6. 12.6 Application Commands
13SPPDMMulti Demo Guide
1. 13.1 Demo Overview
2. 13.2 Demo Application
3. 13.3 Application Commands
14ANP Demo Guide
1. 14.1 Demo Overview
2. 14.2 Demo Application
3. 14.3 Application Commands
15HFP Demo Guide
1. 15.1 Demo Overview
2. 15.2 Demo Application
3. 15.3 Application Commands
16HTP Demo Guide
1. 16.1 Demo Overview
2. 16.2 Demo Application
3. 16.3 Application Commands
17PASP Demo Guide
1. 17.1 Demo Overview
2. 17.2 Demo Application
3. 17.3 Application Commands
18HOGP Demo Guide
1. 18.1 Demo Overview
2. 18.2 Demo Application
3. 18.3 Application Commands
19PXP Demo Guide
1. 19.1 Demo Overview
2. 19.2 Demo Application
3. 19.3 Applications Commands
20FMP Demo Guide
1. 20.1 Demo Overview
2. 20.2 Demo Application
3. 20.3 Application Commands
21CSCP Demo Guide
1. 21.1 Demo Overview
2. 21.2 Demo Application
3. 21.3 Application Commands
22Revision History

20.1 Demo Overview

The Find Me profile defines the behavior when a button is pressed on a device to cause an immediate alert on a peer device. This can be used to allow users to find devices that have been misplaced. There are two roles defined in this profile, Server and the Client.

This application allows the user to use a console to use Bluetooth Low Energy (BLE) to establish connection between two BLE devices, change phone alert status, change ringer status, put in and get out of silent mode.

Note: The same instructions can be used to run this demo on the MSP432 or STM32F4 Platforms.

It is recommended that the user visits the kit setup Getting Started Guide for MSP430, Getting Started Guide for MSP432 or Getting Started Guide for STM32F4 pages before trying the application described on this page.

Running the Bluetooth Code

Once the code is flashed, connect the board to a PC using a miniUSB or microUSB cable. Once connected, wait for the driver to install. It will show up as MSP-EXP430F5438 USB - Serial Port (COM x), XDS110 Class Application/User UART (COM x) for MSP432, under Ports (COM & LPT) in the Device manager. Attach a Terminal program like PuTTY to the serial port x for the board. The serial parameters to use are 115200 Baud (9600 for MSP430), 8, n, 1. Once connected, reset the device using Reset S3 button (located next to the mini USB connector for the MSP430) and you should see the stack getting initialized on the terminal and the help screen will be displayed, which shows all of the commands.

Figure 20-1 FMP Demo Start