ZHCS158C July   2012  – January 2017 ADS1299 , ADS1299-4 , ADS1299-6

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
  4. 修订历史记录
  5. Device Comparison
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements: Serial Interface
    7. 7.7 Switching Characteristics: Serial Interface
    8. 7.8 Typical Characteristics
  8. Parametric Measurement Information
    1. 8.1 Noise Measurements
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Analog Functionality
        1. 9.3.1.1 Input Multiplexer
          1. 9.3.1.1.1 Device Noise Measurements
          2. 9.3.1.1.2 Test Signals (TestP and TestN)
          3. 9.3.1.1.3 Temperature Sensor (TempP, TempN)
          4. 9.3.1.1.4 Supply Measurements (MVDDP, MVDDN)
          5. 9.3.1.1.5 Lead-Off Excitation Signals (LoffP, LoffN)
          6. 9.3.1.1.6 Auxiliary Single-Ended Input
        2. 9.3.1.2 Analog Input
        3. 9.3.1.3 PGA Settings and Input Range
          1. 9.3.1.3.1 Input Common-Mode Range
          2. 9.3.1.3.2 Input Differential Dynamic Range
          3. 9.3.1.3.3 ADC ΔΣ Modulator
          4. 9.3.1.3.4 Reference
      2. 9.3.2 Digital Functionality
        1. 9.3.2.1 Digital Decimation Filter
          1. 9.3.2.1.1 Sinc Filter Stage (sinx / x)
        2. 9.3.2.2 Clock
        3. 9.3.2.3 GPIO
        4. 9.3.2.4 ECG and EEG Specific Features
          1. 9.3.2.4.1 Input Multiplexer (Rerouting the BIAS Drive Signal)
          2. 9.3.2.4.2 Input Multiplexer (Measuring the BIAS Drive Signal)
          3. 9.3.2.4.3 Lead-Off Detection
            1. 9.3.2.4.3.1 DC Lead-Off
            2. 9.3.2.4.3.2 AC Lead-Off (One Time or Periodic)
          4. 9.3.2.4.4 Bias Lead-Off
          5. 9.3.2.4.5 Bias Drive (DC Bias Circuit)
            1. 9.3.2.4.5.1 Bias Configuration with Multiple Devices
    4. 9.4 Device Functional Modes
      1. 9.4.1 Start
        1. 9.4.1.1 Settling Time
      2. 9.4.2 Reset (RESET)
      3. 9.4.3 Power-Down (PWDN)
      4. 9.4.4 Data Retrieval
        1. 9.4.4.1 Data Ready (DRDY)
        2. 9.4.4.2 Reading Back Data
      5. 9.4.5 Continuous Conversion Mode
      6. 9.4.6 Single-Shot Mode
    5. 9.5 Programming
      1. 9.5.1 Data Format
      2. 9.5.2 SPI Interface
        1. 9.5.2.1 Chip Select (CS)
        2. 9.5.2.2 Serial Clock (SCLK)
        3. 9.5.2.3 Data Input (DIN)
        4. 9.5.2.4 Data Output (DOUT)
      3. 9.5.3 SPI Command Definitions
        1. 9.5.3.1  Sending Multi-Byte Commands
        2. 9.5.3.2  WAKEUP: Exit STANDBY Mode
        3. 9.5.3.3  STANDBY: Enter STANDBY Mode
        4. 9.5.3.4  RESET: Reset Registers to Default Values
        5. 9.5.3.5  START: Start Conversions
        6. 9.5.3.6  STOP: Stop Conversions
        7. 9.5.3.7  RDATAC: Read Data Continuous
        8. 9.5.3.8  SDATAC: Stop Read Data Continuous
        9. 9.5.3.9  RDATA: Read Data
        10. 9.5.3.10 RREG: Read From Register
        11. 9.5.3.11 WREG: Write to Register
    6. 9.6 Register Maps
      1. 9.6.1 User Register Description
        1. 9.6.1.1  ID: ID Control Register (address = 00h) (reset = xxh)
        2. 9.6.1.2  CONFIG1: Configuration Register 1 (address = 01h) (reset = 96h)
        3. 9.6.1.3  CONFIG2: Configuration Register 2 (address = 02h) (reset = C0h)
        4. 9.6.1.4  CONFIG3: Configuration Register 3 (address = 03h) (reset = 60h)
        5. 9.6.1.5  LOFF: Lead-Off Control Register (address = 04h) (reset = 00h)
        6. 9.6.1.6  CHnSET: Individual Channel Settings (n = 1 to 8) (address = 05h to 0Ch) (reset = 61h)
        7. 9.6.1.7  BIAS_SENSP: Bias Drive Positive Derivation Register (address = 0Dh) (reset = 00h)
        8. 9.6.1.8  BIAS_SENSN: Bias Drive Negative Derivation Register (address = 0Eh) (reset = 00h)
        9. 9.6.1.9  LOFF_SENSP: Positive Signal Lead-Off Detection Register (address = 0Fh) (reset = 00h)
        10. 9.6.1.10 LOFF_SENSN: Negative Signal Lead-Off Detection Register (address = 10h) (reset = 00h)
        11. 9.6.1.11 LOFF_FLIP: Lead-Off Flip Register (address = 11h) (reset = 00h)
        12. 9.6.1.12 LOFF_STATP: Lead-Off Positive Signal Status Register (address = 12h) (reset = 00h)
        13. 9.6.1.13 LOFF_STATN: Lead-Off Negative Signal Status Register (address = 13h) (reset = 00h)
        14. 9.6.1.14 GPIO: General-Purpose I/O Register (address = 14h) (reset = 0Fh)
        15. 9.6.1.15 MISC1: Miscellaneous 1 Register (address = 15h) (reset = 00h)
        16. 9.6.1.16 MISC2: Miscellaneous 2 (address = 16h) (reset = 00h)
        17. 9.6.1.17 CONFIG4: Configuration Register 4 (address = 17h) (reset = 00h)
  10. 10Applications and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Unused Inputs and Outputs
      2. 10.1.2 Setting the Device for Basic Data Capture
        1. 10.1.2.1 Lead-Off
        2. 10.1.2.2 Bias Drive
      3. 10.1.3 Establishing the Input Common-Mode
      4. 10.1.4 Multiple Device Configuration
        1. 10.1.4.1 Cascaded Mode
        2. 10.1.4.2 Daisy-Chain Mode
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
    1. 11.1 Power-Up Sequencing
    2. 11.2 Connecting the Device to Unipolar (5 V and 3.3 V) Supplies
    3. 11.3 Connecting the Device to Bipolar (±2.5 V and 3.3 V) Supplies
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13器件和文档支持
    1. 13.1 文档支持
      1. 13.1.1 相关文档 
    2. 13.2 相关链接
    3. 13.3 接收文档更新通知
    4. 13.4 社区资源
    5. 13.5 商标
    6. 13.6 静电放电警告
    7. 13.7 Glossary
  14. 14机械、封装和可订购信息

机械、封装和可订购信息

以下页中包括机械、封装和可订购信息。这些信息是针对指定器件可提供的最新数据。这些数据会在无通知且不对本文档进行修订的情况下发生改变。欲获得该数据表的浏览器版本,请查阅左侧的导航栏。