ZHCSHI1H january   2018  – november 2020 CC1312R

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Functional Block Diagram
  5. Revision History
  6. Device Comparison
  7. Terminal Configuration and Functions
    1. 7.1 Pin Diagram – RGZ Package (Top View)
    2. 7.2 Signal Descriptions – RGZ Package
    3. 7.3 Connections for Unused Pins and Modules
  8. Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Power Supply and Modules
    5. 8.5  Power Consumption - Power Modes
    6. 8.6  Power Consumption - Radio Modes
    7. 8.7  Nonvolatile (Flash) Memory Characteristics
    8. 8.8  Thermal Resistance Characteristics
    9. 8.9  RF Frequency Bands
    10. 8.10 861 MHz to 1054 MHz - Receive (RX)
    11. 8.11 861 MHz to 1054 MHz - Transmit (TX) 
    12. 8.12 861 MHz to 1054 MHz - PLL Phase Noise Wideband Mode
    13. 8.13 861 MHz to 1054 MHz - PLL Phase Noise Narrowband Mode
    14. 8.14 359 MHz to 527 MHz - Receive (RX)
    15. 8.15 359 MHz to 527 MHz - Transmit (TX) 
    16. 8.16 359 MHz to 527 MHz - PLL Phase Noise
    17. 8.17 143 MHz to 176 MHz - Receive (RX)
    18. 8.18 143 MHz to 176 MHz  - Transmit (TX) 
    19. 8.19 143 MHz to 176 MHz - PLL Phase Noise
    20. 8.20 Timing and Switching Characteristics
      1. 8.20.1 Reset Timing
      2. 8.20.2 Wakeup Timing
      3. 8.20.3 Clock Specifications
        1. 8.20.3.1 48 MHz Clock Input (TCXO)
        2. 8.20.3.2 48 MHz Crystal Oscillator (XOSC_HF)
        3. 8.20.3.3 48 MHz RC Oscillator (RCOSC_HF)
        4. 8.20.3.4 2 MHz RC Oscillator (RCOSC_MF)
        5. 8.20.3.5 32.768 kHz Crystal Oscillator (XOSC_LF)
        6. 8.20.3.6 32 kHz RC Oscillator (RCOSC_LF)
      4. 8.20.4 Synchronous Serial Interface (SSI) Characteristics
        1. 8.20.4.1 Synchronous Serial Interface (SSI) Characteristics
        2.       43
      5. 8.20.5 UART
        1. 8.20.5.1 UART Characteristics
    21. 8.21 Peripheral Characteristics
      1. 8.21.1 ADC
        1. 8.21.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 8.21.2 DAC
        1. 8.21.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 8.21.3 Temperature and Battery Monitor
        1. 8.21.3.1 Temperature Sensor
        2. 8.21.3.2 Battery Monitor
      4. 8.21.4 Comparators
        1. 8.21.4.1 Low-Power Clocked Comparator
        2. 8.21.4.2 Continuous Time Comparator
      5. 8.21.5 Current Source
        1. 8.21.5.1 Programmable Current Source
      6. 8.21.6 GPIO
        1. 8.21.6.1 GPIO DC Characteristics
    22. 8.22 Typical Characteristics
      1. 8.22.1 MCU Current
      2. 8.22.2 RX Current
      3. 8.22.3 TX Current
      4. 8.22.4 RX Performance
      5. 8.22.5 TX Performance
      6. 8.22.6 ADC Performance
  9. Detailed Description
    1. 9.1  Overview
    2. 9.2  System CPU
    3. 9.3  Radio (RF Core)
      1. 9.3.1 Proprietary Radio Formats
    4. 9.4  Memory
    5. 9.5  Sensor Controller
    6. 9.6  Cryptography
    7. 9.7  Timers
    8. 9.8  Serial Peripherals and I/O
    9. 9.9  Battery and Temperature Monitor
    10. 9.10 µDMA
    11. 9.11 Debug
    12. 9.12 Power Management
    13. 9.13 Clock Systems
    14. 9.14 Network Processor
  10. 10Application, Implementation, and Layout
    1. 10.1 Reference Designs
    2. 10.2 Junction Temperature Calculation
  11. 11Device and Documentation Support
    1. 11.1 Tools and Software
      1. 11.1.1 SimpleLink™ Microcontroller Platform
    2. 11.2 Documentation Support
    3. 11.3 支持资源
    4. 11.4 Trademarks
    5. 11.5 静电放电警告
    6. 11.6 术语表
  12. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Packaging Information

143 MHz to 176 MHz - Receive (RX)

When measured on the CC1352EM-XS169-XS24 reference design with Tc = 25 °C, VDDS = 3.0 V with
DC/DC enabled unless otherwise noted. All measurements are performed at the antenna input with a combined RX and TX path. All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
General Parameters
Spurious emissions 25 MHz to 1 GHz 169.44375 MHz
Conducted emissions measured according to ETSI EN 300 220
< -57 dBm
Spurious emissions 1 GHz to 13 GHz < -47 dBm
WMBUS N-MODE, 4.8 kbps, ±2.4 kHz Deviation, 2-GFSK, 10 kHz RX Bandwidth
Sensitivity 4.8 kbps ± 2.4 kHz BER = 10–2, 169.40625 MHz  –119 dBm
Saturation limit BER = 10–2, 169.40625 MHz 10 dBm
Selectivity, +12.5 kHz (1) BER = 10–2, 169.40625 MHz 51 dB
Selectivity, -12.5 kHz (1) BER = 10–2, 169.40625 MHz 51 dB
Selectivity, +25 kHz (1) BER = 10–2, 169.40625 MHz 52 dB
Selectivity, -25 kHz (1) BER = 10–2, 169.40625 MHz 52 dB
Blocking, +1 MHz (1) BER = 10–2, 169.40625 MHz 73 dB
Blocking, -1 MHz (1) BER = 10–2, 169.40625 MHz 72 dB
Blocking, +2 MHz (1) BER = 10–2, 169.40625 MHz 77 dB
Blocking, -2 MHz (1) BER = 10–2, 169.40625 MHz 75 dB
Blocking, +10 MHz (1) BER = 10–2, 169.40625 MHz 86 dB
Blocking, -10 MHz (1) BER = 10–2, 169.40625 MHz 86 dB
Image rejection (image compensation enabled) (1) BER = 10–2, 169.40625 MHz 46 dB
RSSI dynamic range Starting from the sensitivity limit 91 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
WMBUS N-MODE, 2.4 kbps, ±2.4 kHz Deviation, 2-GFSK, 10 kHz RX Bandwidth
Sensitivity BER = 10–2, 169.43125 MHz –121 dBm
Saturation limit BER = 10–2, 169.43125 MHz 10 dBm
Selectivity, +12.5 kHz (1) BER = 10–2, 169.43125 MHz 51 dB
Selectivity, -12.5 kHz (1) BER = 10–2, 169.43125 MHz 51 dB
Selectivity, +25 kHz (1) BER = 10–2, 169.43125 MHz 52 dB
Selectivity, -25 kHz (1) BER = 10–2, 169.43125 MHz 52 dB
Blocking, +1 MHz (1) BER = 10–2, 169.43125 MHz 74 dB
Blocking, -1 MHz (1) BER = 10–2, 169.43125 MHz 73 dB
Blocking, +2 MHz (1) BER = 10–2, 169.43125 MHz 78 dB
Blocking, -2 MHz (1) BER = 10–2, 169.43125 MHz 77 dB
Blocking, +10 MHz (1) BER = 10–2, 169.43125 MHz 88 dB
Blocking, -10 MHz (1) BER = 10–2, 169.43125 MHz 87 dB
Image rejection (image compensation enabled) (1) BER = 10–2, 169.43125 MHz 50 dB
RSSI dynamic range Starting from the sensitivity limit 92 dB
RSSI accuracy Starting from the sensitivity limit across the given dynamic range ±3 dB
Wanted signal 3 dB above sensitivity limit