ZHCSHT9C August   2021  – June 2024 ADC12DJ4000RF

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics: DC Specifications
    6. 6.6  Electrical Characteristics: Power Consumption
    7. 6.7  Electrical Characteristics: AC Specifications (Dual-Channel Mode)
    8. 6.8  Electrical Characteristics: AC Specifications (Single-Channel Mode)
    9. 6.9  Timing Requirements
    10. 6.10 Switching Characteristics
    11. 6.11 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Inputs
        1. 7.3.1.1 Analog Input Protection
        2. 7.3.1.2 Full-Scale Voltage (VFS) Adjustment
        3. 7.3.1.3 Analog Input Offset Adjust
      2. 7.3.2 ADC Core
        1. 7.3.2.1 ADC Theory of Operation
        2. 7.3.2.2 ADC Core Calibration
        3. 7.3.2.3 Analog Reference Voltage
        4. 7.3.2.4 ADC Overrange Detection
        5. 7.3.2.5 Code Error Rate (CER)
      3. 7.3.3 Temperature Monitoring Diode
      4. 7.3.4 Timestamp
      5. 7.3.5 Clocking
        1. 7.3.5.1 Noiseless Aperture Delay Adjustment (tAD Adjust)
        2. 7.3.5.2 Aperture Delay Ramp Control (TAD_RAMP)
        3. 7.3.5.3 SYSREF Capture for Multi-Device Synchronization and Deterministic Latency
          1. 7.3.5.3.1 SYSREF Position Detector and Sampling Position Selection (SYSREF Windowing)
          2. 7.3.5.3.2 Automatic SYSREF Calibration
      6. 7.3.6 Programmable FIR Filter (PFIR)
        1. 7.3.6.1 Dual Channel Equalization
        2. 7.3.6.2 Single Channel Equalization
        3. 7.3.6.3 Time Varying Filter
      7. 7.3.7 Digital Down Converters (DDC)
        1. 7.3.7.1 Rounding and Saturation
        2. 7.3.7.2 Numerically-Controlled Oscillator and Complex Mixer
          1. 7.3.7.2.1 NCO Fast Frequency Hopping (FFH)
          2. 7.3.7.2.2 NCO Selection
          3. 7.3.7.2.3 Basic NCO Frequency Setting Mode
          4. 7.3.7.2.4 Rational NCO Frequency Setting Mode
          5. 7.3.7.2.5 NCO Phase Offset Setting
          6. 7.3.7.2.6 NCO Phase Synchronization
        3. 7.3.7.3 Decimation Filters
        4. 7.3.7.4 Output Data Format
        5. 7.3.7.5 Decimation Settings
          1. 7.3.7.5.1 Decimation Factor
          2. 7.3.7.5.2 DDC Gain Boost
      8. 7.3.8 JESD204C Interface
        1. 7.3.8.1  Transport Layer
        2. 7.3.8.2  Scrambler
        3. 7.3.8.3  Link Layer
        4. 7.3.8.4  8B/10B Link Layer
          1. 7.3.8.4.1 Data Encoding (8B/10B)
          2. 7.3.8.4.2 Multiframes and the Local Multiframe Clock (LMFC)
          3. 7.3.8.4.3 Code Group Synchronization (CGS)
          4. 7.3.8.4.4 Initial Lane Alignment Sequence (ILAS)
          5. 7.3.8.4.5 Frame and Multiframe Monitoring
        5. 7.3.8.5  64B/66B Link Layer
          1. 7.3.8.5.1 64B/66B Encoding
          2. 7.3.8.5.2 Multiblocks, Extended Multiblocks and the Local Extended Multiblock Clock (LEMC)
          3. 7.3.8.5.3 Block, Multiblock and Extended Multiblock Alignment using Sync Header
            1. 7.3.8.5.3.1 Cyclic Redundancy Check (CRC) Mode
            2. 7.3.8.5.3.2 Forward Error Correction (FEC) Mode
          4. 7.3.8.5.4 Initial Lane Alignment
          5. 7.3.8.5.5 Block, Multiblock and Extended Multiblock Alignment Monitoring
        6. 7.3.8.6  Physical Layer
        7. 7.3.8.7  SerDes Pre-Emphasis
        8. 7.3.8.8  JESD204C Enable
        9. 7.3.8.9  Multi-Device Synchronization and Deterministic Latency
        10. 7.3.8.10 Operation in Subclass 0 Systems
      9. 7.3.9 Alarm Monitoring
        1. 7.3.9.1 NCO Upset Detection
        2. 7.3.9.2 Clock Upset Detection
        3. 7.3.9.3 FIFO Upset Detection
    4. 7.4 Device Functional Modes
      1. 7.4.1 Dual-Channel Mode
      2. 7.4.2 Single-Channel Mode (DES Mode)
      3. 7.4.3 Dual-Input Single-Channel Mode (DUAL DES Mode)
      4. 7.4.4 JESD204C Modes
        1. 7.4.4.1 JESD204C Operating Modes Table
        2. 7.4.4.2 JESD204C Modes continued
        3. 7.4.4.3 JESD204C Transport Layer Data Formats
        4. 7.4.4.4 64B/66B Sync Header Stream Configuration
        5. 7.4.4.5 Dual DDC and Redundant Data Mode
      5. 7.4.5 Power-Down Modes
      6. 7.4.6 Test Modes
        1. 7.4.6.1 Serializer Test-Mode Details
        2. 7.4.6.2 PRBS Test Modes
        3. 7.4.6.3 Clock Pattern Mode
        4. 7.4.6.4 Ramp Test Mode
        5. 7.4.6.5 Short and Long Transport Test Mode
          1. 7.4.6.5.1 Short Transport Test Pattern
          2. 7.4.6.5.2 Long Transport Test Pattern
        6. 7.4.6.6 D21.5 Test Mode
        7. 7.4.6.7 K28.5 Test Mode
        8. 7.4.6.8 Repeated ILA Test Mode
        9. 7.4.6.9 Modified RPAT Test Mode
      7. 7.4.7 Calibration Modes and Trimming
        1. 7.4.7.1 Foreground Calibration Mode
        2. 7.4.7.2 Background Calibration Mode
        3. 7.4.7.3 Low-Power Background Calibration (LPBG) Mode
      8. 7.4.8 Offset Calibration
      9. 7.4.9 Trimming
    5. 7.5 Programming
      1. 7.5.1 Using the Serial Interface
        1. 7.5.1.1 SCS
        2. 7.5.1.2 SCLK
        3. 7.5.1.3 SDI
        4. 7.5.1.4 SDO
        5. 7.5.1.5 Streaming Mode
    6. 7.6 SPI Register Map
  9. 8 Application Information Disclaimer
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Wideband RF Sampling Receiver
        1. 8.2.1.1 Design Requirements
          1. 8.2.1.1.1 Input Signal Path
          2. 8.2.1.1.2 Clocking
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Calculating Values of AC-Coupling Capacitors
        3. 8.2.1.3 Application Curves
    3. 8.3 Initialization Set Up
    4. 8.4 Power Supply Recommendations
      1. 8.4.1 Power Sequencing
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 接收文档更新通知
    4. 9.4 支持资源
    5. 9.5 商标
    6. 9.6 静电放电警告
    7. 9.7 术语表
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.4.4 JESD204C Modes

The ADC12DJ4000RF can be programmed as a single-channel or dual-channel ADC and a number JESD204C output formats. Table 7-21 summarizes the basic operating mode configuration parameters and whether they are user configured or derived.

Table 7-21 ADC12DJ4000RF Operating Mode Configuration Parameters
PARAMETER DESCRIPTION USER CONFIGURED OR DERIVED VALUE
JMODE JESD204C operating mode, automatically derives the rest of the JESD204C parameters, single-channel or dual-channel mode User configured Set by JMODE (see the JESD204C mode register)
DES 1 = single-channel mode, 0 = dual-channel mode Derived See Operating Modes
R Number of bits transmitted per lane per CLK± cycle. The JESD204C line rate is the CLK± frequency times R. This parameter sets the SerDes PLL multiplication factor or controls bypassing of the SerDes PLL. Derived See Operating Modes
Links Number of JESD204C links used Derived See Operating Modes
K Number of frames per multiframe (8B/10B mode) User configured Set by KM1 (see the JESD204C K parameter register), see the allowed values in Operating Modes. This parameter is ignored in 64B/66B modes.
E Number of multiblocks per extended multiblock (64B/66B mode) Derived Always set to '1' in ADC12DJ4000RF. This parameter is ignored in 8B/10B modes.

There are a number of parameters required to define the JESD204C transport layer format, all of which are sent across the link during the initial lane alignment sequence in 8B/10B mode. 64B/66B mode does not use the ILAS, however the transport layer uses the same parameters. In the ADC12DJ4000RF, most parameters are automatically derived based on the selected JMODE; however, a few are configured by the user. Table 7-22 describes these parameters.

Table 7-22 JESD204C Initial Lane Alignment Sequence Parameters
PARAMETERDESCRIPTIONUSER CONFIGURED OR DERIVEDVALUE
ADJCNTLMFC adjustment amount (not applicable)DerivedAlways 0
ADJDIRLMFC adjustment direction (not applicable)DerivedAlways 0
BIDBank IDDerivedAlways 0
CFNumber of control words per frameDerivedAlways 0
CSControl bits per sampleDerivedAlways set to 0 in ILAS, see Operating Modes for actual usage
DIDDevice identifier, used to identify the linkUser configuredSet by DID (see the JESD204C DID parameter register), see Lane Assignments
FNumber of octets (bytes) per frame (per lane)DerivedSee Operating Modes
HDHigh-density format (samples split between lanes)DerivedAlways 0
JESDVJESD204 standard revisionDerivedAlways 1
KNumber of frames per multiframeUser configuredSet by the KM1 register, see the JESD204C K parameter register
LNumber of serial output lanes per linkDerivedSee Operating Modes
LIDLane identifier for each laneDerivedSee Lane Assignments
MNumber of converters used to determine lane bit packing; may not match number of ADC channels in the deviceDerivedSee Operating Modes
NSample resolution (before adding control and tail bits)DerivedSee Operating Modes
N'Bits per sample after adding control and tail bitsDerivedSee Operating Modes
SNumber of samples per converter (M) per frameDerivedSee Operating Modes
SCRScrambler enabledUser configuredSet by the JESD204C control register
SUBCLASSVDevice subclass versionDerivedAlways 1
RES1Reserved field 1DerivedAlways 0
RES2Reserved field 2DerivedAlways 0
CHKSUMChecksum for ILAS checking (sum of all above parameters modulo 256)DerivedComputed based on parameters in this table
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |