ZHCSIN4B August   2018  – June 2021 LM5146-Q1

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 说明（续）
  6. 6 Pin Configuration and Functions
    1. 6.1 Wettable Flanks
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings 
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Input Range (VIN)
      2. 8.3.2  Output Voltage Setpoint and Accuracy (FB)
      3. 8.3.3  High-Voltage Bias Supply Regulator (VCC)
      4. 8.3.4  Precision Enable (EN/UVLO)
      5. 8.3.5  Power Good Monitor (PGOOD)
      6. 8.3.6  Switching Frequency (RT, SYNCIN)
        1. 8.3.6.1 Frequency Adjust
        2. 8.3.6.2 Clock Synchronization
      7. 8.3.7  Configurable Soft Start (SS/TRK)
        1. 8.3.7.1 Tracking
      8. 8.3.8  Voltage-Mode Control (COMP)
      9. 8.3.9  Gate Drivers (LO, HO)
      10. 8.3.10 Current Sensing and Overcurrent Protection (ILIM)
      11. 8.3.11 OCP Duty Cycle Limiter
    4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Active Mode
      4. 8.4.4 Diode Emulation Mode
      5. 8.4.5 Thermal Shutdown
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Design and Implementation
      2. 9.1.2 Power Train Components
        1. 9.1.2.1 Inductor
        2. 9.1.2.2 Output Capacitors
        3. 9.1.2.3 Input Capacitors
        4. 9.1.2.4 Power MOSFETs
      3. 9.1.3 Control Loop Compensation
      4. 9.1.4 EMI Filter Design
    2. 9.2 Typical Applications
      1. 9.2.1 Design 1 – 12-A High-Efficiency Synchronous Buck DC/DC Regulator for Automotive Applications
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
        3. 9.2.1.3 Custom Design With WEBENCH® Tools
        4. 9.2.1.4 Custom Design With Excel Quickstart Tool
        5. 9.2.1.5 Application Curves
      2. 9.2.2 Design 2 – High Density, 12-V, 8-A Rail From 48-V Automotive Battery Power
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
        3. 9.2.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Power Stage Layout
      2. 11.1.2 Gate Drive Layout
      3. 11.1.3 PWM Controller Layout
      4. 11.1.4 Thermal Design and Layout
      5. 11.1.5 Ground Plane Design
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 第三方米6体育平台手机版_好二三四免责声明
      2. 12.1.2 Development Support
        1. 12.1.2.1 Custom Design With WEBENCH® Tools
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
        1. 12.2.1.1 PCB Layout Resources
        2. 12.2.1.2 Thermal Design Resources
    3. 12.3 接收文档更新通知
    4. 12.4 支持资源
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

7.5 Electrical Characteristics

Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over the –40°C to 150°C junction temperature range unless otherwise stated. VVIN = 48 V, VEN/UVLO = 1.5 V, RRT = 25 kΩ unless otherwise stated. (1) (2)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
INPUT SUPPLY
VIN Operating input voltage range IVCC ≤ 10 mA at VVIN = 5.5 V 5.5 100 V
IQ-RUN Operating input current, not switching VEN/UVLO = 1.5 V, VSS/TRK = 0 V 1.8 2.1 mA
IQ-STBY Standby input current VEN/UVLO = 1 V 1.75 2 mA
IQ-SHDN Shutdown input current VEN/UVLO = 0 V, VVCC < 1 V 13.5 30 µA
VCC REGULATOR
VVCC VCC regulation voltage VSS/TRK = 0 V, 9 V ≤ VVIN ≤ 100 V, 0 mA ≤ IVCC ≤ 20 mA 7.3 7.5 7.7 V
VVCC-LDO VIN to VCC dropout voltage VVIN = 6 V, VSS/TRK = 0 V, IVCC = 20 mA 0.25 0.72 V
ISC-LDO VCC short-circuit current VSS/TRK = 0 V, VVCC = 0 V 40 50 70 mA
VVCC-UV VCC undervoltage threshold VVCC rising 4.8 4.93 5.2 V
VVCC-UVH VCC undervoltage hysteresis Rising threshold – falling threshold 0.26 V
VVCC-EXT Minimum external bias voltage Voltage required to disable VCC regulator 8 V
IVCC External VCC input current, not switching VSS/TRK = 0 V, VVCC = 13 V 2.3 mA
ENABLE AND INPUT UVLO
VSHDN Shutdown to standby threshold VEN/UVLO rising 0.42 V
VSHDN-HYS Shutdown threshold hysteresis EN/UVLO Rising threshold – falling threshold 50 mV
VEN Standby to operating threshold VEN/UVLO rising 1.164 1.2 1.236 V
IEN-HYS Standby to operating hysteresis current VEN/UVLO = 1.5 V 9 10 11 µA
ERROR AMPLIFIER
VREF FB reference Voltage FB connected to COMP 792 800 808 mV
IFB-BIAS1 FB input bias current VFB = 0.8 V, –40°C ≤ TJ ≤ 125°C –0.1 0.1 µA
IFB-BIAS2 FB input bias current VFB = 0.8 V, –40℃ ≤ TJ ≤ 150℃ –0.2 0.2 µA
VCOMP-OH COMP output high voltage VFB = 0 V, COMP sourcing 1 mA 5 V
VCOMP-OL COMP output low voltage COMP sinking 1 mA 0.3 V
AVOL DC gain 94 dB
GBW Unity gain bandwidth 6.5 MHz
SOFT-START and VOLTAGE TRACKING
ISS SS/TRK capacitor charging current VSS/TRK = 0 V 8.5 10 12 µA
RSS SS/TRK discharge FET resistance VEN/UVLO = 1 V, VSS/TRK = 0.1 V 11 Ω
VSS-FB SS/TRK to FB offset –15 0 15 mV
VSS-CLAMP SS/TRK clamp voltage VSS/TRK  – VFB, VFB = 0.8 V 115 mV
POWER GOOD INDICATOR
PGUTH FB upper threshold for PGOOD high to low % of VREF, VFB rising 106% 108% 110%
PGLTH FB lower threshold for PGOOD high to low % of VREF, VFB falling 90% 92% 94%
PGHYS_U PGOOD upper theshold hysteresis % of VREF 3%
PGHYS_L PGOOD lower threshold hysteresis % of VREF 2%
TPG-RISE PGOOD rising filter FB to PGOOD rising edge 25% µs
TPG-FALL PGOOD falling filter FB to PGOOD falling edge 25% µs
VPG-OL PGOOD low state output voltage VFB = 0.9 V, IPGOOD = 2 mA 150 mV
IPG-OH PGOOD high state leakage current VFB = 0.8 V, VPGOOD = 13 V 400 nA
OSCILLATOR
FSW1 Oscilator frequency – 1 RRT = 100 kΩ 100 kHz
FSW2 Oscillator frequency – 2 RRT = 25 kΩ 380 400 420 kHz
FSW3 Oscillator frequency – 3 RRT = 12.5 kΩ 780 kHz
SYNCHRONIZATION INPUT AND OUTPUT
FSYNC SYNCIN external clock frequency range % of nominal frequency set by RRT –20% 50%
VSYNC-IH SYNCIN input logic high 2 V
VSYNC-IL SYNCIN input logic low 0.8 V
RSYNC-IN SYNCIN input resistance VSYNCIN = 3 V 20 kΩ
TSYNCI-PW SYNCIN input minimum pulsewidth Minimum high state or low state duration 50 ns
VSYNCO-OH SYNCOUT high-state output voltage ISYNCOUT = –1 mA (sourcing current) 3 V
VSYNCO-OL SYNCOUT low-state output voltage ISYNCOUT = 1 mA (sinking current) 0.4 V
TSYNCOUT Delay from HO rising to SYNCOUT leading edge VSYNCIN = 0 V, TS = 1/FSW, FSW set by RRT TS/2 – 140 ns
TSYNCIN Delay from SYNCIN rising to HO leading edge 50% to 50% 150 ns
GATE DRIVERS
RHO-UP HO high state resistance, HO to BST VBST – VSW = 7 V, IHO = –100 mA 1.5 Ω
RHO-DOWN HO low state resistance, HO to SW VBST – VSW = 7 V, IHO = 100 mA 0.9 Ω
RLO-UP LO high state resistance, LO to VCC VBST – VSW = 7 V, ILO = –100 mA 1.5 Ω
RLO-DOWN LO low state resistance, LO to PGND VBST – VSW = 7 V, ILO = 100 mA 0.9 Ω
IHOH, ILOH HO, LO source current VBST – VSW = 7 V, HO = SW, LO = AGND 2.3 A
IHOL, ILOL HO, LO sink current VBST – VSW = 7 V, HO = BST, LO = VCC 3.5 A
BOOTSTRAP DIODE AND UNDERVOLTAGE THRESHOLD
VBST-FWD Diode forward voltage, VCC to BST VCC to BST, BST pin sourcing 20 mA 0.75 0.9 V
IQ-BST BST to SW quiescent current, not switching VSS/TRK = 0 V, VSW = 48 V, VBST = 54 V 80 µA
VBST-UV BST to SW undervoltage detection VBST – VSW falling 3.4 V
VBST-HYS BST to SW undervoltage hysteresis VBST – VSW rising 0.42 V
PWM CONTROL
tON(min) Minimum controllable on-time VBST – VSW = 7 V, HO 50% to 50% 40 60 ns
tOFF(min) Minimum off-time VBST – VSW = 7 V, HO 50% to 50% 140 200 ns
DC100kHz Maximum duty cycle FSW = 100 kHz, 6 V ≤ VVIN ≤ 60 V 98 99 %
DC400kHz FSW = 400 kHz, 6 V ≤ VVIN ≤ 60 V 90 94 %
VRAMP(min) RAMP valley voltage (COMP at 0% duty cycle) 300 mV
kFF PWM feedforward gain (VIN / VRAMP) 6 V ≤ VVIN ≤ 100 V 15 V/V
OVER CURRENT PROTECT (OCP) – VALLEY CURRENT LIMITING
IRS ILIM source current, RSENSE mode Low voltage detected at ILIM 90 100 110 µA
IRDSON ILIM source current, RDS-ON mode SW voltage detected at ILIM, TJ = 25°C 180 200 220 µA
IRDSONTC ILIM current tempco RDS-ON mode 4500 ppm/°C
IRSTC ILIM current tempco RSENSE mode 0 ppm/°C
VILIM-TH ILIM comparator threshold at ILIM –8 –2 3.5 mV
SHORT CIRCUIT PROTECTION (SCP) –  DUTY CYCLE CLAMP
VCLAMP-OS Clamp offset voltage – no current limiting COMP to duty cycle clamp voltage 0.2 + VVIN/75 V
VCLAMP-MIN Minimum clamp voltage Clamp voltage with continuous current limit 0.3 + VVIN/150 V
HICCUP MODE FAULT PROTECTION
CHICC-DEL Hiccup mode activation delay Clock cycles with current limiting before off-time activated 128 cycles
CHICCUP Hiccup mode off time after activation Clock cycles with no switching followed by SS/TRK release 8192 cycles
DIODE EMULATION / DCM OPERATION
VZCD-SS Zero-cross detect (ZCD) soft-start ramp ZCD threshold measured at SW pin 50 cycles after first HO pulse 0 mV
VZCD-DIS Zero-cross detect disable threshold ZCD threshold measured at SW pin 1000 cycles after first HO pulse 200 mV
VDEM-TH Diode emulation zero-cross threshold Measured at SW with VSW rising –5 0 5 mV
THERMAL SHUTDOWN
TSD Thermal shutdown threshold TJ rising 175 °C
TSD-HYS Thermal shutdown hysteresis 20 °C
(1) All minimum and maximum limits are specified by correlating the electrical characteristics to process and temperature variations and applied statistical process control.
(2) The junction temperature (TJ in ℃) is calculated from the ambient temperature (TA  in ℃) and power dissipation (PD in Watts) as follows: TJ = TA + (PD  × RΘJA) where RΘJA (in ℃/W) is the package thermal impedance provided in . 
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |