ZHCSLL2A May   2021  – March 2022 TPS25830A-Q1 , TPS25832A-Q1

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 说明（续）
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Switching Characteristics
    8. 8.8 Typical Characteristics
  9. 9 Parameter Measurement Information
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
      1. 10.3.1  Buck Regulator
      2. 10.3.2  Enable/UVLO and Start-Up
      3. 10.3.3  Switching Frequency and Synchronization (RT/SYNC)
      4. 10.3.4  Spread-Spectrum Operation
      5. 10.3.5  VCC, VCC_UVLO
      6. 10.3.6  Minimum ON-Time, Minimum OFF-Time
      7. 10.3.7  Internal Compensation
      8. 10.3.8  Bootstrap Voltage (BOOT)
      9. 10.3.9  RSNS, RSET, RILIMIT and RIMON
      10. 10.3.10 Overcurrent and Short Circuit Protection
        1. 10.3.10.1 Current Limit Setting using RILIMIT
        2. 10.3.10.2 Current Limit Setting for MFI OCP
        3. 10.3.10.3 Buck Average Current Limit Design Example
        4. 10.3.10.4 External MOSFET Gate Drivers
        5. 10.3.10.5 Cycle-by-Cycle Buck Current Limit
      11. 10.3.11 Overvoltage, IEC and Short to Battery Protection
        1. 10.3.11.1 VBUS and VCSN/OUT Overvoltage Protection
        2. 10.3.11.2 DP_IN and DM_IN Protection
        3. 10.3.11.3 CC IEC and OVP Protection
      12. 10.3.12 Cable Compensation
        1. 10.3.12.1 Cable Compensation Design Example
      13. 10.3.13 USB Port Control
      14. 10.3.14 FAULT Response
      15. 10.3.15 USB Specification Overview
      16. 10.3.16 USB Type-C® Basics
        1. 10.3.16.1 Configuration Channel
        2. 10.3.16.2 Detecting a Connection
        3. 10.3.16.3 Configuration Channel Pins CC1 and CC2
        4. 10.3.16.4 Current Capability Advertisement and VCONN Overload Protection
        5. 10.3.16.5 Plug Polarity Detection
      17. 10.3.17 Device Power Pins (IN, CSN/OUT, and PGND)
      18. 10.3.18 Thermal Shutdown
      19. 10.3.19 Power Wake
    4. 10.4 Device Functional Modes
      1. 10.4.1 Shutdown Mode
      2. 10.4.2 Standby Mode
      3. 10.4.3 Active Mode
      4. 10.4.4 Device Truth Table (TT)
      5. 10.4.5 USB Port Operating Modes
        1. 10.4.5.1 USB Type-C® Mode
        2. 10.4.5.2 Standard Downstream Port (SDP) Mode — USB 2.0, USB 3.0, and USB 3.1
        3. 10.4.5.3 Charging Downstream Port (CDP) Mode
        4. 10.4.5.4 Client Mode
      6. 10.4.6 High-Bandwidth Data-Line Switches
  11. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Application
      1. 11.2.1 Design Requirements
      2. 11.2.2 Detailed Design Procedure
        1. 11.2.2.1  Output Voltage
        2. 11.2.2.2  Switching Frequency
        3. 11.2.2.3  Inductor Selection
        4. 11.2.2.4  Output Capacitor Selection
        5. 11.2.2.5  Input Capacitor Selection
        6. 11.2.2.6  Bootstrap Capacitor Selection
        7. 11.2.2.7  VCC Capacitor Selection
        8. 11.2.2.8  Enable and Undervoltage Lockout Set-Point
        9. 11.2.2.9  Current Limit Set-Point
        10. 11.2.2.10 Cable Compensation Set-Point
        11. 11.2.2.11 LD_DET, POL, and FAULT Resistor Selection
      3. 11.2.3 Application Curves
  12. 12Power Supply Recommendations
  13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Ground Plane and Thermal Considerations
    3. 13.3 Layout Example
  14. 14Device and Documentation Support
    1. 14.1 Documentation Support
      1. 14.1.1 Related Documentation
    2. 14.2 Related Links
    3. 14.3 接收文档更新通知
    4. 14.4 支持资源
    5. 14.5 Trademarks
    6. 14.6 静电放电警告
    7. 14.7 术语表
  15. 15Mechanical, Packaging, and Orderable Information

8.7 Switching Characteristics

Limits apply over the junction temperature (TJ) range of -40°C to +150°C; VIN = 13.5 V, fSW =400 kHz, CVCC = 2.2 µF, RSNS = 15 mΩ, RIMON = 13 kΩ, RILIMIT= 13 kΩ, RSET= 300 Ω unless otherwise stated. Minimum and maximum limits are specified through test, design or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SOFT START
TSS Internal soft-start time The time of internal reference to increase from 0 V to 1.0 V 3 5 7 ms
HICCUP MODE
NOC Number of cycles that LS current limit is tripped to enter Hiccup mode 128 Cycles
TOC Hiccup retry delay time 118 ms
SW (SW PIN)
TON_MIN Minimum turnon-time 105 ns
TON_MAX Maximum turnon-time, HS timeout in dropout 7.5 µs
TOFF_MIN Minimum turnoff time 80 ns
Dmax Maximum switch duty cycle 98 %
TIMING RESISTOR AND INTERNAL CLOCK
fSW_RANGE Switching frequency range using RT mode 300 2300 kHz
fSW Switching frequency RT = 49.9 kΩ 360 400 440 kHz
Switching frequency RT = 8.66 kΩ 1953 2100 2247 kHz
FSSS Frequency span of spread spectrum operation ±6 %
BUS DISCHARGE
tDEGA_OUT_DCHG Discharge asserting deglitch 5.0 12.5 23.4 ms
tW_BUS_DCHG VBUS discharge time after sink termination removed from CC lines VBUS = 1 V, time ISNK_OUT > 1 mA after sink termination removed from CC lines 150 266 400 ms
CC1/CC2 - VCONN POWER SWITCH 5.1 kΩ ON ONE CC PIN AND 1 kΩ ON THE OTHER
tr Output voltage rise time CL = 1 µF, RL = 100 Ω (measured from 10% to 90% of final value) 0.78 1.1 1.95 ms
tf Output voltage fall time 0.18 0.32 0.38
ton Output voltage turnon-time CL = 1 µF, RL = 100 Ω 4.1 6.2 8.5 ms
toff Output voltage turnoff time 0.5 1 1.6
CC1/CC2 VCONN POWER SWITCH: CURRENT LIMIT
tIOS Short circuit response time 15 µs
CC1/CC2 - CONNECT MANAGEMENT - ATTACH AND DETACH DEGLITCH
tDEGA_CC_ATT Attach asserting deglitch 1.1 2.08 3.29 ms
tDEGD_CC_DET Detach asserting deglitch for exiting UFP state 6.98 12.7 19.4 ms
CC1/CC2 - CONNECT MANAGEMENT - ATTACHED MODE 5.1-kΩ OR 1-kΩ TERMINATION ON AT LEAST ONE CC PIN
tDEGA_CC_SHORT Detach, Rd and Ra asserting deglitch 78 195 366 µs
tDEGA_CC_LONG Long deglitch 87 150 217 ms
CC1/CC2 - CONNECT MANAGEMENT - VCONN DISCHARGED MODE
tW_CC_DCHG Discharge wait time 37 66 99 ms
NFET DRIVER
tr VLS_DR rise time VOUT = 5.1V, NFET = CSD87502Q2, time from LS_GD 10% to 90% 1000 µs
tf VLS_DR fall time VOUT = 5.1 V, NFET = CSD87502Q2, time from LS_GD time 90% to 10% 100 µs
CURRENT LIMIT - EXTERNAL NFET CONNECTED BETWEEN CSN/OUT AND BUS, LS_GD CONNECTED TO FET GATE
tOC_HIC_DEG Deglitch time before hiccup mode 2 ms
tOC_HIC_RST Reset time for exiting hiccup mode 16 ms
tOC_HIC_ON ON-time during hiccup mode 2 ms
tOC_HIC_OFF OFF-time during hiccup mode 263 ms
FAULT DUE TO VBUS OC, VBUS OV, DP OV, DM OV, CC OV, CC OC
tDEGLA Asserting deglitch time 5.5 8.2 11.5 ms
tDEGLD De-asserting deglitch time 5.5 8.2 11.5 ms
LD_DET, POL
tDEGLA Asserting deglitch time 88 150 220 ms
tDEGLD De-asserting deglitch time 7.0 12.7 19.4 ms
HIGH-BANDWIDTH ANALOG SWITCH
tpd Analog switch propagation delay 0.14 ns
tSK Analog switch skew between opposite transitions of the same port (tPHL – tPLH) 0.02 ns
tOV_Dn DP_IN and DM_IN overvoltage protection response time 2 µs
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |