ZHCSMI7A December   2020  – May 2021 TPS92633-Q1

PRODUCTION DATA  

1. 1 特性
2. 2 应用
3. 3 说明
4. 4 Revision History
5. 5 Pin Configuration and Functions
6. 6 Specifications
   1. 6.1 Absolute Maximum Ratings
   2. 6.2 ESD Ratings
   3. 6.3 Recommended Operating Conditions
   4. 6.4 Thermal Information
   5. 6.5 Electrical Characteristics
   6. 6.6 Timing Requirements
   7. 6.7 Typical Characteristics
7. 7 Detailed Description
   1. 7.1 Overview
   2. 7.2 Functional Block Diagram
   3. 7.3 Feature Description
      1. 7.3.1  Power Supply (SUPPLY)
         1. 7.3.1.1 Power-On Reset
         2. 7.3.1.2 Supply Current in Fault Mode
      2. 7.3.2  Enable and Shutdown (EN)
      3. 7.3.3  Reference Current (IREF)
      4. 7.3.4  Constant-Current Output and Setting (INx)
      5. 7.3.5  Analog Current Control (ICTRL)
         1. 7.3.5.1 Off-Board Brightness Binning Resistor
         2. 7.3.5.2 NTC Resistor
      6. 7.3.6  Thermal Sharing Resistor (OUTx and RESx)
      7. 7.3.7  PWM Control (PWMx)
      8. 7.3.8  Supply Control
      9. 7.3.9  Diagnostics
         1. 7.3.9.1 IREF Short-to-GND Detection
         2. 7.3.9.2 IREF Open Detection
         3. 7.3.9.3 LED Short-to-GND Detection
         4. 7.3.9.4 LED Open-Circuit Detection
         5. 7.3.9.5 Single LED Short-Circuit Detection (SLS_REF)
         6. 7.3.9.6 LED Open-Circuit and Single LED Short-Circuit Detection Enable (DIAGEN)
         7. 7.3.9.7 Low Dropout Operation
         8. 7.3.9.8 Over-Temperature Protection
      10. 7.3.10 FAULT Bus Output With One-Fails–All-Fail
      11. 7.3.11 FAULT Table
      12. 7.3.12 LED Fault Summary
      13. 7.3.13 IO Pins Inner Connection
   4. 7.4 Device Functional Modes
      1. 7.4.1 Undervoltage Lockout, V(SUPPLY) < V(POR_rising)
      2. 7.4.2 Normal Operation V(SUPPLY) ≥ 4.5 V
      3. 7.4.3 Low-Voltage Dropout Operation
      4. 7.4.4 Fault Mode
8. 8 Application and Implementation
   1. 8.1 Application Information
   2. 8.2 Typical Applications
      1. 8.2.1 BCM Controlled Rear Lamp with One-Fails-All-Fail Setup
         1. 8.2.1.1 Design Requirements
         2. 8.2.1.2 Detailed Design Procedure
         3. 8.2.1.3 Application Curves
      2. 8.2.2 Independent PWM Controlled Rear Lamp with Off Board LED and Binning Resistor
         1. 8.2.2.1 Design Requirements
         2. 8.2.2.2 Detailed Design Procedure
         3. 8.2.2.3 Application Curves
9. 9 Power Supply Recommendations
10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
11. 11Device and Documentation Support
    1. 11.1 接收文档更新通知
    2. 11.2 支持资源
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
12. 12Mechanical, Packaging, and Orderable Information