ZHCSO54A May   2021  – November 2021 CC1352P7

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
    1. 3.1 功能方框图
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Terminal Configuration and Functions
    1. 6.1 Pin Diagram – RGZ Package (Top View)
    2. 6.2 Signal Descriptions – RGZ Package
    3. 6.3 Connections for Unused Pins and Modules
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Power Supply and Modules
    5. 7.5  Power Consumption - Power Modes
    6. 7.6  Power Consumption - Radio Modes
    7. 7.7  Nonvolatile (Flash) Memory Characteristics
    8. 7.8  Thermal Resistance Characteristics
    9. 7.9  RF Frequency Bands
    10. 7.10 861 MHz to 1054 MHz - Receive (RX)
    11. 7.11 861 MHz to 1054 MHz - Transmit (TX) 
    12. 7.12 861 MHz to 1054 MHz - PLL Phase Noise Wideband Mode
    13. 7.13 861 MHz to 1054 MHz - PLL Phase Noise Narrowband Mode
    14. 7.14 Bluetooth Low Energy - Receive (RX)
    15. 7.15 Bluetooth Low Energy - Transmit (TX)
    16. 7.16 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - RX
    17. 7.17 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - TX
    18. 7.18 Timing and Switching Characteristics
      1. 7.18.1 Reset Timing
      2. 7.18.2 Wakeup Timing
      3. 7.18.3 Clock Specifications
        1. 7.18.3.1 48 MHz Crystal Oscillator (XOSC_HF)
        2. 7.18.3.2 48 MHz RC Oscillator (RCOSC_HF)
        3. 7.18.3.3 2 MHz RC Oscillator (RCOSC_MF)
        4. 7.18.3.4 32.768 kHz Crystal Oscillator (XOSC_LF)
        5. 7.18.3.5 32 kHz RC Oscillator (RCOSC_LF)
      4. 7.18.4 Synchronous Serial Interface (SSI) Characteristics
        1. 7.18.4.1 Synchronous Serial Interface (SSI) Characteristics
        2.       40
      5. 7.18.5 UART
        1. 7.18.5.1 UART Characteristics
    19. 7.19 Peripheral Characteristics
      1. 7.19.1 ADC
        1. 7.19.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 7.19.2 DAC
        1. 7.19.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 7.19.3 Temperature and Battery Monitor
        1. 7.19.3.1 Temperature Sensor
        2. 7.19.3.2 Battery Monitor
      4. 7.19.4 Comparators
        1. 7.19.4.1 Low-Power Clocked Comparator
        2. 7.19.4.2 Continuous Time Comparator
      5. 7.19.5 Current Source
        1. 7.19.5.1 Programmable Current Source
      6. 7.19.6 GPIO
        1. 7.19.6.1 GPIO DC Characteristics
    20. 7.20 Typical Characteristics
      1. 7.20.1 MCU Current
      2. 7.20.2 RX Current
      3. 7.20.3 TX Current
      4. 7.20.4 RX Performance
      5. 7.20.5 TX Performance
      6. 7.20.6 ADC Performance
  8. 8 Detailed Description
    1. 8.1  Overview
    2. 8.2  System CPU
    3. 8.3  Radio (RF Core)
      1. 8.3.1 Proprietary Radio Formats
      2. 8.3.2 Bluetooth 5.2 Low Energy
      3. 8.3.3 802.15.4 (Thread, Zigbee, 6LoWPAN)
    4. 8.4  Memory
    5. 8.5  Sensor Controller
    6. 8.6  Cryptography
    7. 8.7  Timers
    8. 8.8  Serial Peripherals and I/O
    9. 8.9  Battery and Temperature Monitor
    10. 8.10 µDMA
    11. 8.11 Debug
    12. 8.12 Power Management
    13. 8.13 Clock Systems
    14. 8.14 Network Processor
  9. 9 Application, Implementation, and Layout
    1. 9.1 Reference Designs
    2. 9.2 Junction Temperature Calculation
  10. 10Device and Documentation Support
    1. 10.1 Device Nomenclature
    2. 10.2 Tools and Software
      1. 10.2.1 SimpleLink™ Microcontroller Platform
    3. 10.3 Documentation Support
    4. 10.4 支持资源
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 术语表
  11. 11Mechanical, Packaging, and Orderable Information

7.19.2.1 Digital-to-Analog Converter (DAC) Characteristics

Tc = 25 °C, VDDS = 3.0 V, unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
General Parameters
Resolution 8 Bits
VDDS Supply voltage Any load, any VREF, pre-charge OFF, DAC charge-pump ON 1.8 3.8 V
External Load(4), any VREF, pre-charge OFF, DAC charge-pump OFF 2.0 3.8
Any load, VREF = DCOUPL, pre-charge ON 2.6 3.8
FDAC Clock frequency Buffer ON (recommended for external load) 16 250 kHz
Buffer OFF (internal load) 16 1000
Voltage output settling time VREF = VDDS, buffer OFF, internal load 13 1 / FDAC
VREF = VDDS, buffer ON, external capacitive load = 20 pF(3) 13.8
External capacitive load 20 200 pF
External resistive load 10 MΩ
Short circuit current 400 µA
ZMAX Max output impedance Vref = VDDS, buffer ON, CLK 250 kHz VDDS = 3.8 V, DAC charge-pump OFF 50.8 kΩ
VDDS = 3.0 V, DAC charge-pump ON 51.7
VDDS = 3.0 V, DAC charge-pump OFF 53.2
VDDS = 2.0 V, DAC charge-pump ON 48.7
VDDS = 2.0 V, DAC charge-pump OFF 70.2
VDDS = 1.8 V, DAC charge-pump ON 46.3
VDDS = 1.8 V, DAC charge-pump OFF 88.9
Internal Load - Continuous Time Comparator / Low Power Clocked Comparator
DNL Differential nonlinearity VREF = VDDS,
load = Continuous Time Comparator or Low Power Clocked Comparator
FDAC = 250 kHz		 ±1 LSB(1)
Differential nonlinearity VREF = VDDS,
load = Continuous Time Comparator or Low Power Clocked Comparator
FDAC = 16 kHz		 ±1.2
Offset error(2)
Load = Continuous Time Comparator		 VREF = VDDS = 3.8 V ±0.64 LSB(1)
VREF = VDDS = 3.0 V ±0.81
VREF = VDDS = 1.8 V ±1.27
VREF = DCOUPL, pre-charge ON ±3.43
VREF = DCOUPL, pre-charge OFF ±2.88
VREF = ADCREF ±2.37
Offset error(2)
Load = Low Power Clocked Comparator		 VREF = VDDS = 3.8 V ±0.78 LSB(1)
VREF = VDDS = 3.0 V ±0.77
VREF = VDDS = 1.8 V ±3.46
VREF = DCOUPL, pre-charge ON ±3.44
VREF = DCOUPL, pre-charge OFF ±4.70
VREF = ADCREF ±4.11
Max code output voltage variation(2)
Load = Continuous Time Comparator		 VREF = VDDS = 3.8 V ±1.53 LSB(1)
VREF = VDDS = 3.0 V ±1.71
VREF = VDDS = 1.8 V ±2.10
VREF = DCOUPL, pre-charge ON ±6.00
VREF = DCOUPL, pre-charge OFF ±3.85
VREF = ADCREF ±5.84
Max code output voltage variation(2)
Load = Low Power Clocked Comparator		 VREF = VDDS = 3.8 V ±2.92 LSB(1)
VREF =VDDS = 3.0 V ±3.06
VREF = VDDS = 1.8 V ±3.91
VREF = DCOUPL, pre-charge ON ±7.84
VREF = DCOUPL, pre-charge OFF ±4.06
VREF = ADCREF ±6.94
Output voltage range(2)
Load = Continuous Time Comparator		 VREF = VDDS = 3.8 V, code 1 0.03 V
VREF = VDDS = 3.8 V, code 255 3.62
VREF = VDDS = 3.0 V, code 1 0.02
VREF = VDDS = 3.0 V, code 255 2.86
VREF = VDDS = 1.8 V, code 1 0.01
VREF = VDDS = 1.8 V, code 255 1.71
VREF = DCOUPL, pre-charge OFF, code 1 0.01
VREF = DCOUPL, pre-charge OFF, code 255 1.21
VREF = DCOUPL, pre-charge ON, code 1 1.27
VREF = DCOUPL, pre-charge ON, code 255 2.46
VREF = ADCREF, code 1 0.01
VREF = ADCREF, code 255 1.41
Output voltage range(2)
Load = Low Power Clocked Comparator		 VREF = VDDS = 3.8 V, code 1 0.03 V
VREF = VDDS = 3.8 V, code 255 3.61
VREF = VDDS = 3.0 V, code 1 0.02
VREF = VDDS = 3.0 V, code 255 2.85
VREF = VDDS = 1.8 V, code 1 0.01
VREF = VDDS = 1.8 V, code 255 1.71
VREF = DCOUPL, pre-charge OFF, code 1 0.01
VREF = DCOUPL, pre-charge OFF, code 255 1.21
VREF = DCOUPL, pre-charge ON, code 1 1.27
VREF = DCOUPL, pre-charge ON, code 255 2.46
VREF = ADCREF, code 1 0.01
VREF = ADCREF, code 255 1.41
External Load
INL Integral nonlinearity VREF = VDDS, FDAC = 250 kHz ±1 LSB(1)
VREF = DCOUPL, FDAC = 250 kHz ±2
VREF = ADCREF, FDAC = 250 kHz ±1
DNL Differential nonlinearity VREF = VDDS, FDAC = 250 kHz ±1 LSB(1)
Offset error VREF = VDDS = 3.8 V ±0.40 LSB(1)
VREF = VDDS = 3.0 V ±0.50
VREF = VDDS = 1.8 V ±0.75
VREF = DCOUPL, pre-charge ON ±1.55
VREF = DCOUPL, pre-charge OFF ±1.30
VREF = ADCREF ±1.10
Max code output voltage variation VREF = VDDS = 3.8 V ±1.00 LSB(1)
VREF = VDDS = 3.0 V ±1.00
VREF = VDDS = 1.8 V ±1.00
VREF = DCOUPL, pre-charge ON ±3.45
VREF = DCOUPL, pre-charge OFF ±2.10
VREF = ADCREF ±1.90
Output voltage range
Load = Low Power Clocked Comparator		 VREF = VDDS = 3.8 V, code 1 0.03 V
VREF = VDDS = 3.8 V, code 255 3.61
VREF = VDDS = 3.0 V, code 1 0.02
VREF = VDDS = 3.0 V, code 255 2.85
VREF = VDDS = 1.8 V, code 1 0.02
VREF = VDDS = 1.8 V, code 255 1.71
VREF = DCOUPL, pre-charge OFF, code 1 0.02
VREF = DCOUPL, pre-charge OFF, code 255 1.20
VREF = DCOUPL, pre-charge ON, code 1 1.27
VREF = DCOUPL, pre-charge ON, code 255 2.46
VREF = ADCREF, code 1 0.02
VREF = ADCREF, code 255 1.42
(1) 1 LSB (VREF 3.8 V/3.0 V/1.8 V/DCOUPL/ADCREF) = 14.10 mV/11.13 mV/6.68 mV/4.67 mV/5.48 mV
(2) Includes comparator offset
(3) A load > 20 pF will increases the settling time
(4) Keysight 34401A Multimeter
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |