米6体育平台手机版

ZHCSWL7C November 2008 – October 2024 TS3USB221A

PRODUCTION DATA

5.5 Electrical Characteristics

over operating free-air temperature range (unless otherwise noted) ⁽¹⁾

PARAMETER		TEST CONDITIONS		MIN	TYP⁽²⁾	MAX	UNIT
V_IK	Input-Source Clamp Voltage	V_CC = 3.6V, 2.7V, I_I = –18 mA		–1.8			V
I_IN	Input leakage current, control inputs	V_CC = 3.6V, 2.7V, 0V, V_IN = 0V to 3.6V				±1	μA
I_OZ ⁽³⁾	Off-state leakage current	V_CC = 3.6V, 2.7V, V_O = 0V to 5.25V, V_I = 0V, V_IN = V_CC or GND, Switch OFF				±1	μA
I_(OFF)	Power-off leakage current	V_CC = 0V	V_I/O = 0V to 5.25V			±2	μA
			V_I/O = 0V to 3.6V			±2
			V_I/O = 0V to 2.7V			±1
I_CC	Supply Current	V_CC = 3.6V, 2.7V, V_IN = V_CC or GND, I_I/O = 0V, Switch ON or OFF				30	μA
I_CC	Supply Current (low power mode)	V_CC = 3.6V, 2.7V, V_IN = V_CC or GND, Switch disabled, OE in high state				1	μA
ΔI_CC ⁽⁴⁾	Supply-current change, control inputs	One input at 1.8V, Other inputs at V_CC or GND	V_CC = 3.6V			20	μA
ΔI_CC ⁽⁴⁾	Supply-current change, control inputs	One input at 1.8V, Other inputs at V_CC or GND	V_CC = 2.7V			0.5	μA
C_in	Input capacitance, control inputs	V_CC = 3.3V, 2.5V, V_IN = V_CC or 0V			1.5	2.5	pF
C_io(OFF)	OFF capacitance	V_CC = 3.3V, 2.5V, V_I/O = V_CC or 0V, Switch OFF			3.5	5	pF
C_io(ON)	ON capacitance	V_CC = 3.3V, 2.5V, V_I/O = V_CC or 0V, Switch ON			6	7.5	pF
R_ON ⁽⁵⁾	ON-state resistance	V_CC = 3V, 2.3V	V_I = 0V, I_O = 30mA		3	6	Ω
R_ON ⁽⁵⁾	ON-state resistance	V_CC = 3V, 2.3V	V_I = 2.4V, I_O = –15mA		3.4	6	Ω
ΔR_ON	ON-state resistance match between channels	V_CC = 3V, 2.3V	V_I = 0V, I_O = 30mA		0.2		Ω
ΔR_ON	ON-state resistance match between channels	V_CC = 3V, 2.3V	V_I = 1.7, I_O = –15mA		0.2		Ω
R_ON(flat)	ON-state resistance flatness	V_CC = 3V, 2.3V	V_I = 0V, I_O = 30mA		1		Ω
R_ON(flat)	ON-state resistance flatness	V_CC = 3V, 2.3V	V_I = 1.7, I_O = –15mA		1		Ω

(1) V_IN and I_IN refer to control inputs. V_I, V_O, I_I, and I_O refer to data pins.

(2) All typical values are at V_CC = 3.3V (unless otherwise noted), T_A = 25°C.

(3) For I/O ports, the parameter I_OZ includes the input leakage current.

(4) This is the increase in supply current for each input that is at the specified TTL voltage level, rather than V_CC or GND.

(5) Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals.