ZHCSQ68A May   2022  – December 2022 TLIN1431-Q1

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 ESD Ratings, IEC Specification
    4. 6.4 Recommended Operating Conditions
    5. 6.5 Thermal Information
    6. 6.6 Power Supply Characteristics
    7. 6.7 Electrical Characteristics
    8. 6.8 AC Switching Characteristics
    9. 6.9 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 Test Circuit: Diagrams and Waveforms
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  LIN (Local Interconnect Network) Bus
        1. 8.3.1.1 LIN Transmitter Characteristics
        2. 8.3.1.2 LIN Receiver Characteristics
          1. 8.3.1.2.1 Termination
      2. 8.3.2  TXD (Transmit Input and Output)
      3. 8.3.3  RXD (Receive Output)
      4. 8.3.4  WAKE (High Voltage Local Wake Up Input)
      5. 8.3.5  WDT or CLK (Pin Programmable Watchdog Delay Input or SPI Clock)
      6. 8.3.6  WDI or SDI (Watchdog Timer Input or SPI Serial Data In)
      7. 8.3.7  PIN or nCS (Pin Watchdog Select or SPI Chip Select)
      8. 8.3.8  LIMP (Limp Home Output – High Voltage Open Drain Output)
        1. 8.3.8.1 LIMP in Pin Control Mode
        2. 8.3.8.2 LIMP in SPI Control Mode
      9. 8.3.9  nWDR/SDO (Watchdog Timeout Reset Output/SPI Serial Data Out)
      10. 8.3.10 HSS (High-side Switch)
      11. 8.3.11 HSSC or FSO (High-side Switch Control or Function Output)
      12. 8.3.12 WKRQ or INH (Wake Request or Inhibit)
      13. 8.3.13 PV
      14. 8.3.14 DIV_ON
      15. 8.3.15 VBAT (Battery Voltage)
      16. 8.3.16 VSUP (Supply Voltage)
      17. 8.3.17 GND (Ground)
      18. 8.3.18 EN or nINT (Enable Input or Interrupt Output)
      19. 8.3.19 nRST (Reset Input and Reset Output)
      20. 8.3.20 VCC (Supply Output)
      21. 8.3.21 VBAT Voltage Divider
      22. 8.3.22 Protection Features
        1. 8.3.22.1  Sleep Wake Error (SWE) Timer
        2. 8.3.22.2  Device Reset
        3. 8.3.22.3  TXD Dominant Time Out (DTO)
        4. 8.3.22.4  Bus Stuck Dominant System Fault: False Wake Up Lockout
        5. 8.3.22.5  Thermal Shutdown
        6. 8.3.22.6  Under-voltage on VSUP
        7. 8.3.22.7  Unpowered Device and LIN Bus
        8. 8.3.22.8  Floating Pins
        9. 8.3.22.9  VCC Voltage Regulator
          1. 8.3.22.9.1 Under or Over Voltage and Short Circuit
          2. 8.3.22.9.2 Output Capacitance Selection
          3. 8.3.22.9.3 Low-Voltage Tracking
          4. 8.3.22.9.4 Power Supply Recommendation
        10. 8.3.22.10 Watchdog
          1. 8.3.22.10.1 Watchdog in Pin Control Mode
          2. 8.3.22.10.2 Watchdog in SPI Control Mode
          3. 8.3.22.10.3 Watchdog Error Counter
          4. 8.3.22.10.4 Pin Control Mode
          5. 8.3.22.10.5 SPI Control Programming
          6. 8.3.22.10.6 Watchdog Register Relationship
          7. 8.3.22.10.7 Watchdog Timing
      23. 8.3.23 Channel Expansion
        1. 8.3.23.1 Channel Expansion for LIN
        2. 8.3.23.2 Channel Expansion for CAN Transceiver
    4. 8.4 Device Functional Modes
      1. 8.4.1 Init Mode
      2. 8.4.2 Normal Mode
      3. 8.4.3 Fast Mode
      4. 8.4.4 Sleep Mode
      5. 8.4.5 Standby Mode
      6. 8.4.6 Restart Mode
        1. 8.4.6.1 Restart Counter
        2. 8.4.6.2 nRST Behavior in Restart Mode
      7. 8.4.7 Fail-safe Mode
      8. 8.4.8 Wake Up Events
        1. 8.4.8.1 Wake Up Request (RXD)
        2. 8.4.8.2 Local Wake Up (LWU) via WAKE Terminal
          1. 8.4.8.2.1 Static WAKE
          2. 8.4.8.2.2 Cyclic Sense Wake
      9. 8.4.9 Mode Transitions
    5. 8.5 Programming
      1. 8.5.1 SPI Communication
        1. 8.5.1.1 Cyclic Redundancy Check
        2. 8.5.1.2 Chip Select Not (nCS)
        3. 8.5.1.3 Serial Clock Input (CLK)
        4. 8.5.1.4 Serial Data Input (SDI)
        5. 8.5.1.5 Serial Data Output (SDO)
    6. 8.6 Registers
      1. 8.6.1  DEVICE_ID_y Register (Address = 0h + formula) [reset = 0h]
      2. 8.6.2  REV_ID_MAJOR Register (Address = 8h) [reset = 01h]
      3. 8.6.3  REV_ID_MINOR Register (Address = 9h) [reset = 0h]
      4. 8.6.4  CRC_CNTL Register (Address = Ah) [reset = 0h]
      5. 8.6.5  CRC_POLY_SET (Address = Bh) [reset = 00h]
      6. 8.6.6  Scratch_Pad_SPI Register (Address = Fh) [reset = 0h]
      7. 8.6.7  WAKE_PIN_CONFIG1 Register (Address = 11h) [reset = 04h]
      8. 8.6.8  WAKE_PIN_CONFIG2 Register (Address = 12h) [reset = 2h]
      9. 8.6.9  WD_CONFIG_1 Register (Address = 13h) [reset = 90h]
      10. 8.6.10 WD_CONFIG_2 Register (Address = 14h) [reset = 02h]
      11. 8.6.11 WD_INPUT_TRIG Register (Address = 15h) [reset = 0h]
      12. 8.6.12 WD_RST_PULSE Register (Address = 16h) [reset = 40h]
      13. 8.6.13 FSM_CONFIG Register (Address = 17h) [reset = 0h]
      14. 8.6.14 FSM_CNTR Register (Address = 18h) [reset = 0h]
      15. 8.6.15 DEVICE_RST Register (Address = 19h) [reset = 0h]
      16. 8.6.16 DEVICE_CONFIG (Address = 1Ah) [reset = 80h]
      17. 8.6.17 DEVICE_CONFIG2 (Address = 1Bh) [reset = 0h]
      18. 8.6.18 SWE_TIMER (Address = 1Ch) [reset = 30h]
      19. 8.6.19 LIN_CNTL (Address = 1Dh) [reset = 00h]
      20. 8.6.20 HSS_CNTL (Address = 1Eh) [reset = 0h]
      21. 8.6.21 PWM1_CNTL1 (Address = 1Fh) [reset = 0h]
      22. 8.6.22 PWM1_CNTL2 (Address = 20h) [reset = 0h]
      23. 8.6.23 PWM1_CNTL3 (Address = 21h) [reset = 00h]
      24. 8.6.24 PWM2_CNTL1 (Address = 22h) [reset = 0h]
      25. 8.6.25 PWM2_CNTL2 (Address = 23h) [reset = 0h]
      26. 8.6.26 PWM2_CNTL3 (Address = 24h) [reset = 0h]
      27. 8.6.27 TIMER1_CONFIG (Address = 25h) [reset = 00h]
      28. 8.6.28 TIMER2_CONFIG (Address = 26h) [reset = 00h]
      29. 8.6.29 RSRT_CNTR (Address = 28h) [reset = 40h]
      30. 8.6.30 nRST_CNTL (Address = 29h) [reset = 00h]
      31. 8.6.31 INT_GLOBAL Register (Address = 50h) [reset = A0h]
      32. 8.6.32 INT_1 Register (Address = 51h) [reset = 0h]
      33. 8.6.33 INT_2 Register (Address = 52h) [reset = 40h]
      34. 8.6.34 INT_3 Register (Address 53h) [reset = 0h]
      35. 8.6.35 INT_EN_1 Register (Address = 56h) [reset = B0h]
      36. 8.6.36 INT_EN_2 Register (Address = 57h) [reset = 37h]
      37. 8.6.37 INT_EN_3 Register (Address =58h) [reset = BCh]
      38. 8.6.38 INT_4 Register (Address = 5Ah) [reset = 0h]
      39. 8.6.39 INT_EN_4 Register (Address = 5Eh) [reset = CCh]
      40. 8.6.40 Reserved Registers
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Device Brownout Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Normal Mode Application Note
        2. 9.2.1.2 Standby Mode Application Note
        3. 9.2.1.3 TXD Dominant State Timeout Application Note
      2. 9.2.2 Detailed Design Procedures
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 商标
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RGY|20
散热焊盘机械数据 (封装 | 引脚)
订购信息

1 特性

  • AEC-Q100（等级 1）：符合汽车应用要求
  • 功能安全型
  • 符合本地互连网络 (LIN) 物理层规范 LIN 2.2A、ISO 17987–4:2016 和 SAE J2602:2021 要求
  • 由引脚或串行外设接口 SPI 配置的集成看门狗监控器
  • 支持 12V 应用的增强功能
    • ±58V LIN 总线故障保护
    • 采用 12V 电源供电时支持 125mA 电流的 3.3V (TLIN14313-Q1) 或 5V (TLIN14315-Q1) LDO 输出
    • 开路负载和短路检测由 10 位 PWM 或计时器控制的高侧开关
    • 可配置为高侧开关的 LIMP 引脚
    • 支持不同输入阈值或方法的可配置 WAKE 引脚
    • 睡眠模式：超低电流消耗支持以下类型的唤醒事件：
      • LIN 总线
      • 通过 WAKE 引脚实施的本地唤醒
        • 循环和静态感测
  • 保护特性：
    • ESD 保护
    • VSUP 和 VCC 欠压保护
    • TXD 显性超时 (DTO) 保护
    • 热关断保护
  • 集成式电池电压监测器
  • 采用无引线 QFN (20) 封装，具有改善的自动光学检测 (AOI) 功能
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |