Home Data converters Integrated & special-function data converters Medical AFEs Biosensing AFEs
Home
Data converters
Integrated & special-function data converters
Medical AFEs
Biosensing AFEs

AFE4410

ACTIVE

Low power integrated AFE with FIFO for wearable optical heart-rate monitoring and biosensing

Order now
Data sheet

AFE4410

ACTIVE
Data sheet Order now

Product details

Applications Optical-HRM Number of input channels 3 Resolution (bps) 22 Number of LEDs 4 Interface type I2C, SPI Operating temperature range (°C) -20 to 70 Rating Catalog
Applications Optical-HRM Number of input channels 3 Resolution (bps) 22 Number of LEDs 4 Interface type I2C, SPI Operating temperature range (°C) -20 to 70 Rating Catalog
DSBGA (YZ) 30 4.8 mm² 2.4 x 2
  • Accurate, Continuous Heart-Rate Monitoring:
    • Up to 100-dB Dynamic Range for Accurate Heart-Rate Detection
    • Low Current for Continuous Operation on a Wearable Device With a Typical Value:
      • 30 µA for an LED, 25 µA for the Receiver
  • Transmitter:
    • 4 LEDs in Common Anode Configurations
    • 8-Bit Programmable LED Current to 200 mA
    • Mode to Fire Two LEDs in Parallel
    • Programmable LED On-Time
    • Simultaneous Support of 3 LEDs for Optimized SpO2, HRM, or Multiwavelength HRM
    • Average Current of 30 µA Adequate for a Typical Heart-Rate Monitoring Scenario:
      • 20-mA Setting, 60-µs Pulse Duration,
        25-Hz Sampling Rate
  • Receiver:
    • Supports 3 Time-Multiplexed PD Inputs
    • 24-Bit Representation of Current Input From PD in Two’s-Complement Format
    • Individual DC Offset Subtraction DAC
      (Up to ±127-µA Range) at TIA Input for Each LED, Ambient
    • Digital Ambient Subtraction at ADC Output
    • Transimpedance Gain: 10 kΩ to 2 MΩ
    • Noise Filtering With Programmable Bandwidth
    • Receiver Operates at Approximately 1-µA/Hz Sampling Rate (Example, 25 µA at 25 Hz)
    • Hardware Power-Down Mode: Approximately 0-µA Current
  • Flexible Pulse Sequencing and Timing Control
  • Clocking Via External Clock or Internal Oscillator
  • FIFO With 128-Sample Depth:
    • Programmable Partitioning Across Phases
  • Pin-Selectable I2C, SPI Interface
  • Operating Temperature Range: –20°C to +70°C
  • 2.6-mm × 2.1-mm, 0.4-mm Pitch DSBGA Package
  • Supplies:
    • Tx: 3 V to 5.25 V
    • Rx: 1.8 V to 1.9 V (LDO Bypass),
      2.0 V to 3.6 V (LDO Enabled)
    • IO: 1.7 V to Rx_SUP
  • Accurate, Continuous Heart-Rate Monitoring:
    • Up to 100-dB Dynamic Range for Accurate Heart-Rate Detection
    • Low Current for Continuous Operation on a Wearable Device With a Typical Value:
      • 30 µA for an LED, 25 µA for the Receiver
  • Transmitter:
    • 4 LEDs in Common Anode Configurations
    • 8-Bit Programmable LED Current to 200 mA
    • Mode to Fire Two LEDs in Parallel
    • Programmable LED On-Time
    • Simultaneous Support of 3 LEDs for Optimized SpO2, HRM, or Multiwavelength HRM
    • Average Current of 30 µA Adequate for a Typical Heart-Rate Monitoring Scenario:
      • 20-mA Setting, 60-µs Pulse Duration,
        25-Hz Sampling Rate
  • Receiver:
    • Supports 3 Time-Multiplexed PD Inputs
    • 24-Bit Representation of Current Input From PD in Two’s-Complement Format
    • Individual DC Offset Subtraction DAC
      (Up to ±127-µA Range) at TIA Input for Each LED, Ambient
    • Digital Ambient Subtraction at ADC Output
    • Transimpedance Gain: 10 kΩ to 2 MΩ
    • Noise Filtering With Programmable Bandwidth
    • Receiver Operates at Approximately 1-µA/Hz Sampling Rate (Example, 25 µA at 25 Hz)
    • Hardware Power-Down Mode: Approximately 0-µA Current
  • Flexible Pulse Sequencing and Timing Control
  • Clocking Via External Clock or Internal Oscillator
  • FIFO With 128-Sample Depth:
    • Programmable Partitioning Across Phases
  • Pin-Selectable I2C, SPI Interface
  • Operating Temperature Range: –20°C to +70°C
  • 2.6-mm × 2.1-mm, 0.4-mm Pitch DSBGA Package
  • Supplies:
    • Tx: 3 V to 5.25 V
    • Rx: 1.8 V to 1.9 V (LDO Bypass),
      2.0 V to 3.6 V (LDO Enabled)
    • IO: 1.7 V to Rx_SUP

TheAFE4410is an analog front-end for optical biosensing applications, such as heart rate monitoring (HRM). The device supports a maximum of four switching light-emitting diodes (LEDs) and a maximum of three photodiodes (PDs). The electrical current from the photodiode is converted into voltage by the transimpedance amplifier (TIA) and digitized using an analog-to-digital converter (ADC). The ADC code is stored in a 128-sample first-in, first-out block (FIFO) with programmable depth. The FIFO can be read out using either an I2C interface or a serial peripheral interface (SPI). The AFE also has a fully integrated LED driver with 8-bit current control. The device has high dynamic range transmit-and-receive circuitry offering a dynamic range of up to 100 dB that enables accurate heart ratesensing. The AFE achieves extremely low current levels by operating an ultralow power (ULP) mode set by using the ENABLE_ULP register bit.

TheAFE4410is an analog front-end for optical biosensing applications, such as heart rate monitoring (HRM). The device supports a maximum of four switching light-emitting diodes (LEDs) and a maximum of three photodiodes (PDs). The electrical current from the photodiode is converted into voltage by the transimpedance amplifier (TIA) and digitized using an analog-to-digital converter (ADC). The ADC code is stored in a 128-sample first-in, first-out block (FIFO) with programmable depth. The FIFO can be read out using either an I2C interface or a serial peripheral interface (SPI). The AFE also has a fully integrated LED driver with 8-bit current control. The device has high dynamic range transmit-and-receive circuitry offering a dynamic range of up to 100 dB that enables accurate heart ratesensing. The AFE achieves extremely low current levels by operating an ultralow power (ULP) mode set by using the ENABLE_ULP register bit.
filter Find other Biosensing AFEs
Download View video with transcript Video
More Information

Full data sheet and other design resources are available under NDA. Request now

Similar products you might be interested in

open-in-new Compare alternates
Same functionality with different pin-out to the compared device
AFE44I30 ACTIVE Ultra-low-power integrated analog front end (AFE) for wearable optical biosensing with FIFO and I2C Higher SNR, 6 LEDs, 4 PDs, and improved automatic ambient and LED cancellation.
AFE44S30 ACTIVE Ultra-low-power integrated analog front end (AFE) for wearable optical biosensing with FIFO and SPI Higher SNR, 8 LEDs, 4 PDs, and improved automatic ambient and LED cancellation.

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 2
Type Title Date
* Data sheet AFE4410 Ultra-Small, Integrated AFE With FIFO for Wearable, Continuous Optical Heart-Rate Monitoring and Biosensing datasheet (Rev. B) PDF | HTML 31 Jul 2019
Technical article Optical heart-rate sensors for biometric wearables PDF | HTML 03 May 2018

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

AFE4403EVM — AFE4403 Integrated AFE for Heart-Rate Monitors and Pulse Oximeters Evaluation Module

The AFE4403EVM is intended for evaluating the AFE4403 device. The fully integrated AFE is ideally suited for Pulse Oximeter and Heart rate monitoring applications and consists of low noise receive channel, the LED transmit section and diagnostics for sensor and LED fault detection. The AFE4403 has (...)

User guide: PDF
Not available on TI.com
Evaluation board

AFE4410EVM — AFE4410 Integrated AFE With FIFO for Wearable Optical Heart-Rate Monitoring Evaluation Module

The AFE4410 is an analog front end (AFE) for optical biosensing applications, such as heart-rate monitoring (HRM) and saturation of peripheral capillary oxygen (SpO2). The device supports four switching light-emitting diodes (LEDs) and three photodiodes. The current from the photodiode is converted (...)

Request
Evaluation board

AFE4490SPO2EVM — AFE4490 Integrated Analog Front End (AFE) for Pulse Oximeters Evaluation Module

The AFE44x0SPO2EVM is intended for evaluating AFE4400 and AFE4490 devices. The family of devices are fully integrated AFE ideally suited for Pulse Oximeter applications and consist of low noise receive channel, the LED transmit section and diagnostics for sensor and LED fault detection. The (...)

User guide: PDF
Not available on TI.com
Simulation tool

PSPICE-FOR-TI — PSpice® for TI design and simulation tool

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Request
Package Pins CAD symbols, footprints & 3D models
DSBGA (YZ) 30 Ultra Librarian
TI's Standard Terms and Conditions for Evaluation Items apply.

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring
Information included:
  • Fab location
  • Assembly location

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

View all forum topics

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos