Typical values are at TA =
25°C, nominal supply voltages, default full-scale voltage (FS_RANGE_A = FS_RANGE_B =
0xA000), fIN = 347MHz, AIN = –1dBFS, fCLK = 1.5GHz,
filtered 1VPP sine-wave clock, DES_EN = 1, LDEMUX = 1, LALIGNED = 0,
ADC_DITH = 0x01, LVDS driver high-swing mode (HSM) and foreground calibration; SNR
results exclude DC, HD2 to HD9 and interleaving spurs; SINAD, ENOB, and SFDR results
exclude DC and signal-independent interleaving spurs (fS / 4 and
fS / 2 spurs)
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-98 SNR
vs Input Frequency
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-100 SINAD
vs Input Frequency
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-102 ENOB
vs Input Frequency
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-104 SFDR
vs Input Frequency
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-106 HD2
and HD3 vs Input Frequency
| DES_EN = 0, fS = 1500MHz, FG
calibration, includes fS / 2 – fIN
spur only |
Figure 5-108 Worst
Interleaving Spur vs Input Frequency
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-110 SNR vs Sampling Rate
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-112 SINAD vs Sampling Rate
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-114 ENOB vs Sampling Rate
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-116 SFDR vs Sampling Rate
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-118 SNR vs Input Power
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-120 SINAD vs Input Power
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-122 ENOB vs Input Power
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-124 SFDR vs Input Power
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-126 SNR vs Clock Amplitude
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-128 SINAD vs Clock Amplitude
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-130 ENOB vs Clock Amplitude
| DES_EN = 0, fS = 1500MHz, FG
calibration |
Figure 5-132 SFDR vs Clock Amplitude
| DES_EN = 0,
fS = 1500MHz, FG calibration,
SNR = 57.5dBFS, SFDR = 73.8dBFS, ENOB = 9.2 bits |
Figure 5-134 Single-Tone FFT at fIN = 99MHz, AIN = –1dBFS
| DES_EN = 0,
fS = 1500MHz, FG calibration,
SNR = 57.6dBFS, SFDR = 71.7dBFS, ENOB = 9.2 bits |
Figure 5-136 Single-Tone FFT at fIN = 347MHz, AIN = –1dBFS
| DES_EN = 0,
fS = 1500MHz, FG calibration,
SNR = 57.2dBFS, SFDR = 63.5dBFS, ENOB = 8.9 bits |
Figure 5-138 Single-Tone FFT at fIN = 797MHz, AIN = –1dBFS
| DES_EN = 1,
fS = 3000MHz, FG calibration,
SNR = 56.2dBFS, SFDR = 62.8dBFS, ENOB = 8.7 bits |
Figure 5-140 Single-Tone FFT at fIN = 2488MHz, AIN =
–1dBFS
| DES_EN = 1,
fS = 3000MHz, FG calibration,
f1 = 89MHz, f2 = 99MHz,
AIN = -7dBFS per tone, SFDR = -74dBFS,
IMD3 = -90dBFS, IMD2 = -82dBFS |
Figure 5-142 Two-Tone FFT at fIN = 94MHz, AIN = –1dBFS
| DES_EN = 1,
fS = 3000MHz, FG calibration,
f1 = 342MHz, f2 = 352MHz,
AIN = -7dBFS per tone, SFDR = -71dBFS,
IMD3 = -88dBFS, IMD2 = -73dBFS |
Figure 5-144 Two-Tone FFT at fIN = 347MHz, AIN = –1dBFS
| DES_EN = 1,
fS = 3000MHz, FG calibration,
f1 = 792MHz, f2 = 802MHz,
AIN = -7dBFS per tone, SFDR = -71dBFS,
IMD3 = -84dBFS, IMD2 = -77dBFS |
Figure 5-146 Two-Tone FFT at fIN = 797MHz, AIN = –1dBFS
| DES_EN = 0,
fS = 1500MHz, FG calibration,
FIN = 99MHz |
Figure 5-148 DNL
vs Code
| DES_EN = 1,
fS = 3000MHz, FG calibration,
FIN = 99MHz |
Figure 5-150 DNL
vs Code
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-152 SNR vs Temperature and Calibration Mode
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-154 SINAD vs Temperature and Calibration Mode
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-156 ENOB vs Temperature and Calibration Mode
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-158 SFDR vs Temperature and Calibration Mode
| DES_EN = 0, fS = 1500MHz,
FIN = 99MHz, AIN =
-1dBFS |
Figure 5-160 Power
Consumption vs Temperature
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-162 Performance vs VA19 Supply Voltage
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-164 Performance vs VA11 Supply Voltage
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-166 Performance vs VD11 Supply Voltage
| DES_EN = 0, fS = 1500MHz,
FIN = 347MHz, AIN =
-1dBFS |
Figure 5-168 Performance vs VLVDS Supply Voltage
| DES_EN = 0,
fS = 1500MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-170 VA19 Supply Current vs Clock Rate
| DES_EN = 0,
fS = 1500MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-172 VA11 Supply Current vs Clock Rate
| DES_EN = 0,
fS = 1500MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-174 VD11 Supply Current vs Clock Rate
| DES_EN = 0,
fS = 1500MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-176 VLVDS Supply Current vs Clock Rate
| DES_EN = 0,
fS = 1500MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-178 Power Consumption vs Clock Rate
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-99 SNR
vs Input Frequency
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-101 SINAD
vs Input Frequency
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-103 ENOB
vs Input Frequency
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-105 SFDR
vs Input Frequency
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-107 HD2
and HD3 vs Input Frequency
| DES_EN = 1,
fS = 3000MHz, FG calibration,
includes fS / 2 – fIN and
fS /4 ± fIN spurs only |
Figure 5-109 Worst
Interleaving Spur vs Input Frequency
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-111 SNR vs Sampling Rate
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-113 SINAD vs Sampling Rate
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-115 ENOB vs Sampling Rate
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-117 SFDR vs Sampling Rate
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-119 SNR vs Input Power
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-121 SINAD vs Input Power
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-123 ENOB vs Input Power
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-125 SFDR vs Input Frequency
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-127 SNR vs Clock Amplitude
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-129 SINAD vs Clock Amplitude
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-131 ENOB vs Clock Amplitude
| DES_EN = 1,
fS = 3000MHz, FG
calibration |
Figure 5-133 SFDR vs Clock Amplitude
| DES_EN = 1,
fS = 3000MHz, FG calibration,
SNR = 57.4dBFS, SFDR = 71.3dBFS, ENOB = 9.0 bits |
Figure 5-135 Single-Tone FFT at fIN = 99MHz, AIN = –1dBFS
| DES_EN = 1,
fS = 3000MHz, FG calibration,
SNR = 57.6dBFS, SFDR = 64.2dBFS, ENOB = 9.1 bits |
Figure 5-137 Single-Tone FFT at fIN = 347MHz, AIN = –1dBFS
| DES_EN = 1,
fS = 3000MHz, FG calibration,
SNR = 57.3dBFS, SFDR = 62.8dBFS, ENOB = 8.9 bits |
Figure 5-139 Single-Tone FFT at fIN = 797MHz, AIN = –1dBFS
| DES_EN = 0,
fS = 1500MHz, FG calibration,
f1 = 89MHz, f2 = 99MHz,
AIN = -7dBFS per tone, SFDR = -73dBFS,
IMD3 = -98dBFS, IMD2 = -83dBFS |
Figure 5-141 Two-Tone FFT at fIN = 94MHz, AIN = –1dBFS
| DES_EN = 0,
fS = 1500MHz, FG calibration,
f1 = 342MHz, f2 = 352MHz,
AIN = -7dBFS per tone, SFDR = -74dBFS,
IMD3 = -92dBFS, IMD2 = -81dBFS |
Figure 5-143 Two-Tone FFT at fIN = 347MHz, AIN = –1dBFS
| DES_EN = 0,
fS = 1500MHz, FG calibration,
f1 = 792MHz, f2 = 802MHz,
AIN = -7dBFS per tone, SFDR = -74dBFS,
IMD3 = -90dBFS, IMD2 = -82dBFS |
Figure 5-145 Two-Tone FFT at fIN = 797MHz, AIN = –1dBFS
| DES_EN = 1,
fS = 3000MHz, FG calibration,
f1 = 2483MHz, f2 = 2493MHz,
AIN = -7dBFS per tone, SFDR = -70dBFS,
IMD3 = -74dBFS, IMD2 = -75dBFS |
Figure 5-147 Two-Tone FFT at fIN = 2488MHz, AIN =
–1dBFS
| DES_EN = 0,
fS = 1500MHz, FG calibration,
FIN = 99MHz |
Figure 5-149 INL
vs Code
| DES_EN = 1,
fS = 3000MHz, FG calibration,
FIN = 99MHz |
Figure 5-151 INL
vs Code
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-153 SNR vs Temperature and Calibration Mode
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-155 SINAD vs Temperature and Calibration Mode
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-157 ENOB vs Temperature and Calibration Mode
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-159 SFDR vs Temperature and Calibration Mode
| DES_EN = 1,
fS = 3000MHz, FIN =
99MHz, AIN = -1dBFS |
Figure 5-161 Power
Consumption vs Temperature
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-163 Performance vs VA19 Supply Voltage
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-165 Performance vs VA11 Supply Voltage
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-167 Performance vs VD11 Supply Voltage
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-169 Performance vs VLVDS Supply Voltage
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-171 VA19 Supply Current vs Clock Rate
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-173 VA11 Supply Current vs Clock Rate
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-175 VD11 Supply Current vs Clock Rate
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-177 VLVDS Supply Current vs Clock Rate
| DES_EN = 1,
fS = 3000MHz, FIN =
347MHz, AIN = -1dBFS |
Figure 5-179 Power Consumption vs Clock Rate