ZHCSPF6B february   2022  – may 2023 LMQ66410 , LMQ66420 , LMQ66430

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 System Characteristics
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Enable, Start-Up, and Shutdown
      2. 8.3.2  Adjustable Switching Frequency (with RT)
      3. 8.3.3  Power-Good Output Operation
      4. 8.3.4  Internal LDO, VCC, and VOUT/FB Input
      5. 8.3.5  Bootstrap Voltage and VBOOT-UVLO (BOOT Terminal)
      6. 8.3.6  Output Voltage Selection
      7. 8.3.7  Spread Spectrum
      8. 8.3.8  Soft Start and Recovery from Dropout
        1. 8.3.8.1 Recovery from Dropout
      9. 8.3.9  Current Limit and Short Circuit
      10. 8.3.10 Thermal Shutdown
      11. 8.3.11 Input Supply Current
    4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Active Mode
        1. 8.4.3.1 CCM Mode
        2. 8.4.3.2 Auto Mode – Light Load Operation
          1. 8.4.3.2.1 Diode Emulation
          2. 8.4.3.2.2 Frequency Reduction
        3. 8.4.3.3 FPWM Mode – Light Load Operation
        4. 8.4.3.4 Minimum On-Time (High Input Voltage) Operation
        5. 8.4.3.5 Dropout
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Synchronous Buck Regulator at 400 kHz
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
        1. 9.2.3.1  Choosing the Switching Frequency
        2. 9.2.3.2  Setting the Output Voltage
          1. 9.2.3.2.1 VOUT / FB for Adjustable Output
        3. 9.2.3.3  Inductor Selection
        4. 9.2.3.4  Output Capacitor Selection
        5. 9.2.3.5  Input Capacitor Selection
        6. 9.2.3.6  CBOOT
        7. 9.2.3.7  VCC
        8. 9.2.3.8  CFF Selection
        9. 9.2.3.9  External UVLO
        10. 9.2.3.10 Maximum Ambient Temperature
      4. 9.2.4 Application Curves
    3. 9.3 Best Design Practices
    4. 9.4 Power Supply Recommendations
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
        1. 9.5.1.1 Ground and Thermal Considerations
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 第三方米6体育平台手机版_好二三四免责声明
      2. 10.1.2 Device Nomenclature
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 接收文档更新通知
    4. 10.4 支持资源
    5. 10.5 Trademarks
    6. 10.6 静电放电警告
    7. 10.7 术语表
  12. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.5 Electrical Characteristics

Limits apply over the recommended operating junction temperature range of -40°C to +150°C, unless otherwise noted. Minimum and Maximum limits are specified through test, design or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 13.5V, VOUT = 3.3V. 
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE (VIN PIN)
VINMIN Input voltage rising threshold for startup Before startup 3.2 3.35 3.5 V
Input voltage falling threshold Once operating 2.45 2.7 3 V
ISD(VIN) Shutdown quiescent current at VIN pin EN = 0 V 0.25 1 µA
IBIAS Non-switching input current at VOUT/FB Fixed 5.0-V Vout, VVOUT/FB = 5.25 V 4.2 6.5 µA
IBIAS Non-switching input current at VOUT/FB Fixed 3.3-Vout, VVOUT/FB = 3.47 V 4.2 6.5 µA
IQVIN(nonsw) Non-switching input current; measured at VIN pin (1) Fixed 5-V VOUT, VVOUT/FB = 5.25 V 1.6 3 µA
IQVIN(nonsw) Non-switching input current; measured at VIN pin (1) Fixed 3.3-V VOUT, VVOUT/FB = 3.47 V 1.2 2.2 µA
ENABLE (EN PIN)
VEN-WAKE EN wakeup threshold 0.5 0.7 1 V
VEN-VOUT Precision enable rising threshold for VOUT 1.16 1.23 1.3 V
VEN-HYST Enable hysteresis below VEN-VOUT 0.3 0.35 0.4 V
ILKG-EN Enable pin input leakage current VEN = VIN = 13.5 V 10 nA
INTERNAL LDO (VCC PIN)
VCC VCC pin output voltage VFB = 0 V, IVCC = 1 mA 3.1 3.3 3.45 V
VOLTAGE FEEDBACK (VOUT/FB PIN)
VOUT Output voltage accuracy for fixed VOUT 3.3-V VOUT, VIN = 3.6 V to 36 V, FPWM Mode 3.27 3.3 3.32 V
5-V VOUT, VIN = 5.5 V to 36 V, FPWM Mode 4.94 5.00 5.06 V
VFB Internal reference voltage accuracy VOUT = 1 V, VIN = 3.0 V to 36 V, FPWM Mode 0.99 1.00 1.01 V
IFB(LKG) FB input current Adjustable configuration, FB = 1 V 10 nA
CURRENT LIMITS
IPEAKMAX High-side peak current limit LMQ66430 3.9 4.4 5 A
IVALMAX Low-side valley current limit LMQ66430 2.9 3.5 4 A
IPEAKMIN Minimum peak current limit LMQ66430, Auto Mode 0.55 0.69 0.86 A
INEGMIN Low-side valley current negative limit LMQ66430, FPWM Mode –1.5 –1.3 –1 A
IPEAKMAX High-side peak current limit LMQ66420 2.8 3.4 3.9 A
IVALMAX Low-side valley current limit  LMQ66420 1.9 2.2 2.53 A
IPEAKMIN Minimum peak current limit  LMQ66420, Auto Mode 0.37 0.5 0.65 A
INEGMIN Negative current limit  LMQ66420, FPWM Mode –1 –0.8 –0.6 A
IPEAKMAX High-side peak current limit LMQ66410 1.4 1.8 2.1 A
IVALMAX Low-side valley current limit LMQ66410 0.9 1.1 1.4 A
IPEAKMIN Minimum peak current limit LMQ66410, Auto Mode 0.17 0.27 0.35 A
INEGMIN Low-side valley current negative limit LMQ66410, FPWM Mode –1 –0.8 –0.6 A
IZC Zero-cross current limit Auto Mode 30 80 135 mA
POWER GOOD (PG PIN)
PGOV PG upper threshold - rising % of VOUT/FB (Fixed or Adj. output) 104 108 111 %
PGUV PG upper threshold - falling % of VOUT/FB (Fixed or Adj. output) 89 91 94.2 %
PGHYST PG recovery hysteresis for OV % of VOUT/FB target regulation voltage 2 2.4 2.8 %
PG recovery hysteresis for UV % of VOUT/FB target regulation voltage 2 3.3 4.6 %
VPG-VAL Minimum VIN for PG function VEN = 0 V, RPG_PU = 10 kΩ 1.5 V
RPG PG ON resistance VEN = 3.3 V, 200 µA pull up current 100 Ω
RPG PG ON resistance VEN = 0 V, 200 µA pull up current 100 Ω
tRESET_FILTER PG deglitch delay at falling edge 25 40 75 µs
tPG_ACT Delay time to PG high signal 1.35 2.5 4 ms
SOFT START
tSS Time from first SW pulse to VOUT/FB at 90% of set point 2 3.5 4.6 ms
tHICCUP Time in hiccup before retry soft start 30 50 75 ms
FSW(2.2MHz) Switching Frequency with fixed 2.2 MHz 2100 2200 2300 kHz
OSCILLATOR (RT PIN)
fADJ Frequency adjust range 0.25 2.2 MHz
FSW(2p2MHz) Switching frequency with fixed 2.2 MHz RT pin tied to GND 2100 2200 2300 kHz
FSW(Adj) Accuracy of external frequency, 400 kHz RRT = 39.2 kΩ 0.1% resistor 340 400 460 kHz
Accuracy of external frequency, 2.2 MHz RRT = 6.92 kΩ 0.1% resistor 2100 2200 2450 kHz
SWITCH NODE
tON-MIN Minimum HS switch on-time FPWM mode IOUT = 1 A, 2.2 MHz fixed 65 75 ns
tOFF-MIN Minimum HS switch off-time 60 85 ns
tON-MAX Maximum HS switch on-time HS timeout in dropout 6 9 13 µs
POWER STAGE
VBOOT_UVLO Voltage on BOOT pin compared to SW which will turnoff high-side switch 2.1 V
RDSON-HS High-side MOSFET on-resistance Load = 1 A 132 260 mΩ
RDSON-LS Low-side MOSFET on-resistance Load = 1 A 75 140 mΩ
(1) This is the current used by the device open loop. It does not represent the total input current of the system when in regulation.
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |