2 修订历史记录

从修订版本 D 更改为修订版本 E

Changes from January 22, 2019 to December 9, 2019

• Changed the note that begins "Supply voltage changes faster than 0.2 V/µs can trigger a BOR reset..." in Section 5.3, Recommended Operating ConditionsGo
• Added the note that begins "TI recommends that power to the DVCC pin must not exceed the limits..." in Section 5.3, Recommended Operating ConditionsGo
• Changed the note that begins "A capacitor tolerance of ±20% or better is required..." in Section 5.3, Recommended Operating ConditionsGo
• Added the note "See MSP430 32-kHz Crystal Oscillators for details on crystal section, layout, and testing" to Table 5-3, XT1 Crystal Oscillator (Low Frequency)Go
• Changed the note that begins "Requires external capacitors at both terminals..." in Table 5-3, XT1 Crystal Oscillator (Low Frequency)Go
• Added the t_(int) parameter in Table 5-8, Digital InputsGo
• Corrected the test conditions for the R_I,MUX parameter in Table 5-17, ADC, Power Supply and Input Range ConditionsGo
• Added the note that begins "t_Sample = ln(2ⁿ⁺¹) × τ ..." in Table 5-18, ADC, 10-Bit Timing ParametersGo

Changes from August 30, 2018 to January 21, 2019

• 已通篇将调制振荡器 (MODOSC) 更改为调制振荡器时钟 (MODCLK)Go
• Added "or memory corruption" to note (1) in Section 5.1, Absolute Maximum RatingsGo
• Added the note that begins "The VLO clock frequency is reduced by..." after Table 5-6, Internal Very-Low-Power Low-Frequency Oscillator (VLO)Go
• Changed the parameter symbol from R_I to R_I,MUX in Table 5-17, ADC, Power Supply and Input Range ConditionsGo
• Added the R_I,Misc parameter in Table 5-17, ADC, Power Supply and Input Range ConditionsGo
• Removed ADCDIV from the formula for the t_CONVERT TYP value, because ADCCLK is after division, in Table 5-18, ADC, 10-Bit Timing ParametersGo
• Added note (2) for R_I calculation in Table 5-18, ADC, 10-Bit Timing ParametersGo
• Removed "±3°C" on both temperatures in the note that begins "The device descriptor structure contains..." in Table 5-19, ADC, 10-Bit Linearity Parameters Go
• Add "10b" for ADCSSEL bit in Table 6-6, Clock DistributionGo
• Added Figure 6-1, Clock Distribution Block DiagramGo
• Corrected the spelling of the IRDSSEL bit in the paragraph that begins "The IR functions are controlled by..." in Section 6.9.8, Timers (Timer0_A3, Timer1_A3)Go
• Changed two instances of "ADC 1.5-V Reference Temperature" to "ADC 1.5-V Reference Temperature Sensor" in Table 6-29, Device DescriptorsGo

Changes from August 15, 2015 to August 29, 2018

• Updated Section 3.1, Related ProductsGo
• Replaced all notes on Section 5.11, Thermal CharacteristicsGo
• Added note to V_SVSH- and V_SVSH+ parameters in Table 5-1, PMM, SVS and BORGo
• Updated the link to the BSL user's guide in Section 6.4, Bootloader (BSL)Go
• Changed all instances of "bootstrap loader" to "bootloader" throughout documentGo
• Corrected the ADCINCHx column heading in Table 6-12, ADC Channel ConnectionsGo
• 更新了Section 8，器件和文档支持 中的特定于器件的信息和链接Go

Changes from December 23, 2014 to August 14, 2015

• Corrected "10-BIT ADC CHANNELS" column for MSP430FR2032IPM in Table 3-1, Device ComparisonGo
• Added T_stg MIN and MAX valuesGo
• Added Section 5.2, ESD RatingsGo
• Changed all graphs in Section 5.9, Typical Characteristics, Low-Power Mode Supply Currents, for new measurements Go
• Added V_{REF, 1.2V} parameter to Table 5-1, PMM, SVS and BORGo
• Changed t_STE,LEAD MIN value at 2 V from 40 ns to 50 nsGo
• Changed t_STE,LEAD MIN value at 3 V from 24 ns to 45 nsGo
• Changed t_VALID,SO MAX value at 2 V from 55 ns to 65 nsGo
• Changed t_VALID,SO MAX value at 3 V from 30 ns to 40 nsGo
• Changed the f_ADCOSC TYP value from 4.5 MHz to 5.0 MHzGo
• In Table 6-1, Operating Modes, changed the entry for "Power Consumption at 25°C, 3 V" in AM from 100 µA/MHz to 126 µA/MHzGo
• In Table 6-1, Operating Modes, added "with RTC only" to the entry for "Power Consumption at 25°C, 3 V" in LPM3.5Go
• In Table 6-2, Interrupt Sources, Flags, and Vectors, removed "FRAM access time error" (ACCTEIFG) from the "System NMI" row Go

Changes from October 3, 2014 to December 22, 2014

• Moved T_stg to Absolute Maximum RatingsGo
• Changed link to BSL user's guide in Section 6.4, Bootloader (BSL)Go
• Added note (1) to Table 6-6Go
• Changed the values of ADC Calibration Tag and ADC Calibration Length in the ADC Calibration rowGo
• Added Calibration Tag, Calibration Length, and 1.5-V Reference in the Reference and DCO Calibration rowGo
• Added row for BSL memory to Table 6-30Go