2 修订历史记录

从修订版本 D 更改为修订版本 E

Changes from August 29, 2018 to December 9, 2019

• Updated Section 3.1, Related ProductsGo
• Changed the note that begins "Supply voltage changes faster than 0.2 V/µs can trigger a BOR reset..." in Section 5.3, Recommended Operating ConditionsGo
• Added the note that begins "TI recommends that power to the DVCC pin must not exceed the limits..." in Section 5.3, Recommended Operating ConditionsGo
• Changed the note that begins "A capacitor tolerance of ±20% or better is required..." in Section 5.3, Recommended Operating ConditionsGo
• Corrected "SVS Enabled" test condition on Figure 5-2, LPM3.5 Supply Current vs TemperatureGo
• Added the note "See MSP430 32-kHz Crystal Oscillators for details on crystal section, layout, and testing" to Table 5-3, XT1 Crystal Oscillator (Low Frequency)Go
• Changed the note that begins "Requires external capacitors at both terminals..." in Table 5-3, XT1 Crystal Oscillator (Low Frequency)Go
• Changed the parameter symbol from R_I to R_I,MUX in Table 5-20, ADC, Power Supply and Input Range ConditionsGo
• Corrected the test conditions for the R_I,MUX parameter in Table 5-20, ADC, Power Supply and Input Range ConditionsGo
• Added R_I,Misc TYP value of 34 kΩ in Table 5-20, ADC, Power Supply and Input Range ConditionsGo
• Added formula for R_I in Table 5-21, ADC, 10-Bit Timing ParametersGo
• Added the note that begins "t_Sample = ln(2ⁿ⁺¹) × τ ..." in Table 5-21, ADC, 10-Bit Timing ParametersGo
• Corrected bitfield from RTCCLK to RTCCKSEL in Table 6-8, Clock DistributionGo
• Corrected bitfield from IRDSEL to IRDSSEL in Section 6.11.8, Timers (Timer0_B3, Timer1_B3) , in the description that starts "The interconnection of Timer0_B3 and ..."Go
• Added P1SELC information in Table 6-31, Port P1, P2 Registers (Base Address: 0200h)Go
• Added P2SELC information in Table 6-31, Port P1, P2 Registers (Base Address: 0200h)Go
• Added note to "ADC calibration" in Table 6-46, Device DescriptorsGo

Changes from September 12, 2017 to August 28, 2018

• Updated Section 3.1, Related ProductsGo
• Added note to V_SVSH- and V_SVSH+ parameters in Table 5-1, PMM, SVS and BORGo
• Corrected ADCINCHx column heading in Table 6-16, ADC Channel ConnectionsGo
• 更新了Section 8.2器件命名规则 中的文本和图Go

Changes from June 1, 2016 to September 11, 2017

• 更正了“关断模式 (LPM4.5)” 特性 列表项中的电流Go
• 根据测试数据，低泄漏输入从 50pA 降为 5pAGo
• Added Section 3.1, Related ProductsGo
• Removed ADCDIV from the formula for the TYP value in the second row of the t_CONVERT parameter in Table 5-21, ADC, 10-Bit Timing Parameters (removed because ADCCLK is after division)Go
• Changed the entries for eUSCI_A0 and eUSCI_B0 in the LPM3 column from Off to Optional in Table 6-1, Operating ModesGo
• Added the sentence that begins "This device supports blank device detection..." in Section 6.6, Bootloader (BSL)Go
• Added the note "Controlled by the RTCCLK bit in the SYSCFG2 register" on Table 6-8, Clock DistributionGo
• Added Figure 6-1, Clock Distribution Block DiagramGo
• Added Figure 6-2, Timer_B ConnectionsGo
• Removed SYSBERRIV register (not supported) in Table 6-26, SYS RegistersGo
• Changed from "If the RST/NMI pin is unused...with a 2.2-nF pulldown capacitor" to "If the RST/NMI pin is unused...with a 10-nF pulldown capacitor"Go

Changes from March 30, 2016 to May 31, 2016

• 将器件状态从“米6体育平台手机版_好二三四预发布”更改为“生产数据” Go
• Changed the value of f_XT1 in the table note that starts "Low-power mode 4, VLO,..."Go
• Added Test Conditions to module Timer_B in Section 5.10, Typical Characteristics – Current Consumption Per ModuleGo
• Added "16 MHz" to the parameter description of t_{FLL, lock} in Table 5-5, DCO FLLGo
• Removed ±3℃ from calibration temperatures in the table note that starts "The device descriptor structure contains calibration values..."Go
• Changed the unit on the E_NI parameter in Table 5-24, SAC0 (SAC-L1, OA)Go
• Changed the unit on the E_NI parameter in Table 5-25, TIA0Go

Changes from February 23, 2016 to March 29, 2016

• 已将整篇文档中 TIA 模块的名称由“TRI0”更改为“TIA0”Go
• Changed TYP values for the I_{AM, FRAM}(0%) parameter in Section 5.4, Active Mode Supply Current Into V_CC Excluding External CurrentGo
• Changed MAX values of the t_VALID,SO parameter in Table 5-18, eUSCI (SPI Slave Mode) Switching CharacteristicsGo
• Changed the TYP value of the CMRR parameter with Test Conditions of "TRIPM = 0" from 70 dB to 80 dB in Table 5-25, TIA0Go
• Changed the TYP value of the PSRR parameter with Test Conditions of "TRIPM = 0" from 70 dB to 80 dB in Table 5-25, TIA0Go
• 已将旧版中的开发工具支持部分替换为Section 8.3，工具和软件Go