ZHCSN45B December   2021  – December 2023 SN75LVPE5412

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 DC Electrical Characteristics
    6. 5.6 High Speed Electrical Characteristics
    7. 5.7 SMBUS/I2C Timing Characteristics
    8. 5.8 Typical Characteristics
    9. 5.9 Typical Jitter Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Five-Level Control Inputs
      2. 6.3.2 Linear Equalization
      3. 6.3.3 Flat Gain
      4. 6.3.4 Receiver Detect State Machine
    4. 6.4 Device Functional Modes
      1. 6.4.1 Active PCIe Mode
      2. 6.4.2 Active Buffer Mode
      3. 6.4.3 Standby Mode
    5. 6.5 Programming
      1. 6.5.1 Pin Mode
      2. 6.5.2 SMBUS/I2C Register Control Interface
        1. 6.5.2.1 Shared Registers
        2. 6.5.2.2 Channel Registers
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 PCIe x8 Lane Switching
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
      2. 7.2.2 Protocol Agnostic Linear Redriver for High Speed Interfaces
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 接收文档更新通知
    2. 8.2 支持资源
    3. 8.3 Trademarks
    4. 8.4 静电放电警告
    5. 8.5 术语表
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RUA|42
散热焊盘机械数据 (封装 | 引脚)
订购信息

4 Pin Configuration and Functions

GUID-20210120-CA0I-QJZ0-CC16-0JKJ5PH9G9S6-low.gif Figure 4-1 RUA Package, 42-Pin WQFN (Top View)
Table 4-1 Pin Functions
PIN TYPE(1) DESCRIPTION
NAME NO.
MODE 41 I, 5-level Sets device control configuration modes. The 5-level IO pin is defined in Table 6-1. The pin can be exercised at device power up or in normal operation mode.
L0: Pin Mode – device control configuration is done solely by strap pins.
L1 or L2: SMBus/I2C Mode – device control configuration is done by an external controller with SMBus/I2C primary. This pin along with ADDR pin sets devices secondary address.
L3 and L4 (Float): RESERVED – TI internal test modes.
EQ0 /ADDR 40 I, 5-level In Pin Mode:
The EQ0 and EQ1 pins sets receiver linear equalization CTLE (AC gain) for all channels according to Table 6-2. These pins are sampled at device power-up only.
In SMBus/I2C Mode:
The ADDR pin in conjunction with MODE pin sets SMBus / I2C secondary address according to Table 6-5. The pin is sampled at device power-up only.
EQ1 20 I, 5-level
GAIN /SDA 1 I, 5-level / IO In Pin Mode:
Flat gain (broadband gain – DC and AC) from the input to the output of the device for all channels. Note: the device also provides AC (high frequency) gain in the form of equalization controlled by EQ pins or SMBus/I2C registers. The pin is sampled at device power-up only.
In SMBus/I2C Mode:
3.3V SMBus/I2C data. External pullup resistor such as 4.7 kΩ required for operation.
GND EP, 6, 9, 16, 21, 30, 39 P Ground reference for the device.
EP: the Exposed Pad at the bottom of the QFN package. It is used as the GND return for the device. The EP should be connected to one or more ground planes through the low resistance path. A via array provides a low impedance path to GND. The EP also improves thermal dissipation.
PD 18 I, 3.3V LVCMOS 2-level logic controlling the operating state of the redriver. Active in both Pin Mode and SMBus/I2C Mode. The pin is used part of PCIe RX_DET state machine as outlined in Table 6-4.
High: power down for all channels
Low: power up, normal operation for all channels
RSVD1, 2 2, 12 — Reserved pins – for best signal integrity performance connect the pins to GND. Alternate option would be 0 Ω resistors from pins to GND.
RX_DET /SCL 42 I, 5-level / IO In Pin Mode:
Sets receiver detect state machine options according to Table 6-4. The pin is sampled at device power-up only.
In SMBus/I2C Mode:
3.3V SMBus/I2C clock. External pullup resistor such as 4.7 kΩ required for operation.
RX0N 4 I Inverting differential RX inputs. Channel 0.
RX0P 3 I Noninverting differential RX inputs. Channel 0.
RX1N 8 I Inverting differential RX inputs. Channel 1.
RX1P 7 I Noninverting differential RX inputs. Channel 0.
RX2N 11 I Inverting differential RX inputs. Channel 2.
RX2P 10 I Noninverting differential RX inputs. Channel 2.
RX3N 15 I Inverting differential RX inputs. Channel 3.
RX3P 14 I Noninverting differential RX inputs. Channel 3.
SEL 17 I, 3.3V LVCMOS Selects the mux path. Active in both Pin Mode and SMBus/I2C Mode. The pin has a weak internal pull-down resistor. Note: the SEL pin must be exercised in system implementations for mux selection between Port A vs Port B. The pin is used for PCIe RX_DET state machine as outlined in Table 6-4.
L: Port A selected.
H: Port B selected.
TXA0N 37 O Inverting differential TX output – Port A, Channel 0.
TXA0P 38 O Non-inverting differential TX output – Port A, Channel 0.
TXA1N 33 O Inverting differential TX output – Port A, Channel 1.
TXA1P 34 O Non-inverting differential TX output – Port A, Channel 1.
TXA2N 28 O Inverting differential TX output – Port A, Channel 2.
TXA2P 29 O Non-inverting differential TX output – Port A, Channel 2.
TXA3N 24 O Inverting differential TX output – Port A, Channel 3.
TXA3P 25 O Non-inverting differential TX output – Port A, Channel 3.
TXB0N 35 O Inverting differential TX output – Port B, Channel 0.
TXB0P 36 O Non-inverting differential TX output – Port B, Channel 0.
TXB1N 31 O Inverting differential TX output – Port B, Channel 1.
TXB1P 32 O Non-inverting differential TX output – Port B, Channel 1.
TXB2N 26 O Inverting differential TX output – Port B, Channel 2.
TXB2P 27 O Non-inverting differential TX output – Port B, Channel 2.
TXB3N 22 O Inverting differential TX output – Port B, Channel 3.
TXB3P 23 O Non-inverting differential TX output – Port B, Channel 3.
TEST 19 O TI internal test pin. Keep no connect.
VCC 5, 13 P Power supply, VCC = 3.3V ± 10%. The VCC pins on this device should be connected through a low-resistance path to the board VCC plane.
(1) I = input, O = output, P = power, GND = ground
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |