SNOK006 April   2024 TPS7H6013-SP

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1Device Information
    1. 1.1 Product Description
    2. 1.2 Device Details
  5. 2Total Dose Test Setup
    1. 2.1 Test Overview
    2. 2.2 Test Description and Facilities
    3. 2.3 Test Setup Details
      1. 2.3.1 Unbiased
      2. 2.3.2 Biased
    4. 2.4 Test Configuration and Condition
  6. 3TID Characterization Test Results
    1. 3.1 TID Characterization Results Summary
    2. 3.2 Data Sheet Electrical Parameters
  7. 4Applicable and Reference Documents
    1. 4.1 Applicable Documents
    2. 4.2 Reference Documents
  8.   A Appendix: HDR TID Report

3.2 Data Sheet Electrical Parameters

Specifications are at ambient temperature TA = 25°C, VIN = 10V to 14V, VBP5L = VBP5H = 5V, and no load on LOH, LOL, HOH, and HOL (unless otherwise noted).

Table 3-1 TPS7H60x3-SP Data Sheet Electrical Parameters
Parameter Test Conditions MIN MAX UNIT Test Number
SUPPLY CURRENTS
IQLS Low-side quiescent current VIN = 12V, BOOT = 10V MODE = PWM, EN = 0V 6.8 mA 35.0, 36.0, 37.0
MODE = IIM, LI = HI = 0V 8 35.2, 36.2, 37.2
IQHS High-side quiescent current VIN = 12V, BOOT = 10V MODE = PWM, EN = 0V 6.3 mA 35.1, 36.1, 37.1
MODE = IIM, LI = HI = 0V 6.3 35.3, 36.3, 37.3
IOP_LS Low-side operating current MODE = PWM, no load for HOL and HOH f = 500kHz 9 mA 35.6, 36.6, 37.6
f = 1MHz 11 35.8, 36.8, 37.8
f = 2MHz 16 35.10, 36.10, 37.10
f = 5MHz 30 35.12, 36.12, 37.12
MODE = IIM, no load for HOL and HOH f = 500kHz 9 35.14, 36.14, 37.14
f = 1MHz 12 35.16, 36.16, 37.16
f = 2MHz 17 35.18, 36.18, 37.18
f = 5MHz 30 35.20, 36.20, 37.20
IOP_HS High-side operating current MODE = PWM, no load for HOL and HOH f = 500kHz 6.5 mA 35.7, 36.7, 37.7
f = 1MHz 8 35.9, 36.9, 37.9
f = 2MHz 10.5 35.11, 36.11, 37.11
f = 5MHz 17.5 35.13, 36.13, 37.13
MODE = IIM, no load for HOL and HOH f = 500kHz 6.5 35.15, 36.15, 37.15
f = 1MHz 8 35.17, 36.17, 37.17
f = 2MHz 10.5 35.19, 36.19, 37.19
f = 5MHz 15 35.21, 36.21, 37.21
GATE DRIVER
VOL Low-level output voltage IOL = 100mA 0.15 V 45.0, 46.0, 47.0
BP5x – VOH High-level output voltage IOH = 100mA 0.3 V 45.2, 46.2, 47.2
IOH Peak source current HOH, LOH = 0V, BP5x = 5V 0.7 2.3 A 50.0, 50.1, 51.0, 51.1, 52.0, 52.1
IOL Peak sink current HOL, LOL = 5V, BP5x = 5V 1.6 4.6 A 50.2, 51.2, 52.2
INTERNAL REGULATORS
VBP5L Low-side 5V regulator output voltage CBP5L = 1µF 4.75 5.175 V 60.1, 60.4, 60.7, 60.10, 60.13, 60.16, 60.19, 60.22, 61.1, 61.4, 61.7, 61.10, 61.13, 61.16, 61.19, 61.22, 62.1, 62.4, 62.7, 62.10, 62.13, 62.16, 62.19, 62.22
VBP5H High-side 5V regulator output voltage CBP5H = 1µF 4.75 5.175 V 60.2, 60.5, 60.8, 60.11, 60.14, 60.17, 60.20, 60.23, 61.2, 61.5, 61.8, 61.11, 61.14, 61.17, 61.20, 61.23, 62.2, 62.5, 62.8, 62.11, 62.14, 62.17, 62.20, 62.23
VBP7L 7V regulator output voltage CBP7L = 1µF 6.65 7.35 V 60.0, 60.3, 60.6, 60.9, 60.12, 60.15, 60.18, 60.21, 61.0, 61.3, 61.6, 61.9, 61.12, 61.15, 61.18, 61.21, 61.23, 62.0, 62.3, 62.6, 62.9, 62.12, 62.15, 62.18, 62.21
UNDERVOLTAGE PROTECTION
BP5HR BP5H UVLO rising threshold CBP5H = 1µF 4 4.5 V 85.1, 86.1, 87.1(1)
BP5HF BP5H UVLO falling threshold CBP5H = 1µF 3.8 4.3 V 85.2, 86.2, 87.2(1)
BP5LR BP5L UVLO rising threshold CBP5L = 1µF 4. 4.5 V 80.1, 81.1, 82.1(1)
BP5LF BP5L UVLO falling threshold CBP5L = 1µF 3.8 4.3 V 80.2, 81.2, 82.2(1)
BP7LR BP7L UVLO rising threshold CBP7L = 1µF 6.2 6.8 V 80.4, 81.4, 82.4(1)
BP7LF BP7L UVLO falling threshold CBP7L = 1µF 5.9 6.5 V 80.5, 81.5, 82.5(1)
VINR VIN UVLO rising threshold 8 9 V 70
VINF VIN UVLO falling threshold 7.5 8.5 V 70.1
BOOTR BOOT UVLO rising threshold 6.6 7.4 V 75
BOOTF BOOT UVLO falling threshold 6.2 7 V 75.1
INPUT PINS
VIR Input rising edge threshold 1.80 2.65 V 90.0, 91.0, 92.0, 90.3, 91.3, 92.3
VIF Input falling edge threshold 1.15 1.85 V 90.1, 91.1, 92.1, 90.4, 91.4, 92.4
RPD Input pull-down resistance V = 2.15V applied at input (EN_HI or PWM_LI) 100 400 kΩ 90.6, 90.7, 91.6, 91.7, 92.6, 92.7
PROGRAMMABLE DEAD TIME
TDLH LO off to HO on dead time MODE = PWM, LO falling to HO rising (90% to 10%), f ≤ 2MHz RLH = 3.32kΩ 0 10 ns 95.0, 95.5, 95.10, 96.0, 96.5, 96.10, 97.0, 97.5, 97.10
RLH = 11.8kΩ 8 15.5 95.1, 95.6, 95.11, 96.1, 96.6, 96.11, 97.1, 97.6, 97.11
RLH = 21kΩ 15.5 24 95.2, 95.7, 95.12, 96.2, 96.7, 96.12, 97.2, 97.7, 97.12
RLH = 52.3kΩ 36 59 95.3, 95.8, 95.13, 96.3, 96.8, 96.13, 97.3, 97.8, 97.13
RLH = 105kΩ 74 113.5 95.4, 95.9, 95.14, 96.4, 96.9, 96.14, 97.4, 97.9, 97.14
TDHL HO off to LO on dead time MODE = PWM, HO falling to LO rising (90% to 10%), f ≤ 2MHz RHL = 7.87kΩ 0 10 ns 95.19, 95.24, 95.29, 96.19, 96.24, 96.29, 97.19, 97.24, 97.29
RHL = 13.3kΩ 6 15 95.20, 95.25, 95.30, 96.20, 96.25, 96.30, 97.20, 97.25, 97.30
RHL = 23.7kΩ 16 24.5 95.21, 95.26, 95.31, 96.21, 96.26, 96.31, 97.21, 97.26, 97.31
RHL = 57.6kΩ 44 61 95.22, 95.27, 95.32, 96.22, 96.27, 96.32, 97.22, 97.27, 97.32
RHL = 113kΩ 86 125 95.23, 95.28, 95.33, 96.23, 96.28, 96.33, 97.23, 97.28, 97.33
BOOTSTRAP DIODE SWITCH
Bootstrap diode switch parallel resistance IBST_SW = 1mA 0.8 1.2 kΩ 100.1, 101.1, 102.1
POWER GOOD
Logic-low output IFLT= 1mA 0.4 V 105.0, 106.0, 107.0
PGOOD internal resistance BP5L = 5V, BP7L = 7V, VIN = 12V 0.7 1.9 MΩ 105.2, 106.2, 107.2
Minimum BP5L voltage for valid PGOOD output 2.45 V 105.1, 106.1, 107.1
(1) Tests are only tested in production or SPI Test Mode.

Table 3-2 TPS7H60x3-SP Switching Characteristics
ParameterTest ConditionsMINMAXUNITTest Number
tLPHLLO turnoff propagation delayMODE = PWMPWM rising to LOL falling48ns110.0, 111.0, 112.0
MODE = IIMLI falling to LOL falling38ns110.3, 110.7, 111.3, 111.7, 112.3, 112.7
tLPLHLO turnon propagation delayMODE = IIMLI rising to LOH rising38ns110.2, 110.6, 111.2, 111.6, 112.2, 112.6
tHPHLHO turnoff propagation delayMODE = PWMPWM falling to HOL falling50ns110.1, 111.1,112.1
MODE = IIMHI falling to HOL falling40110.5, 110.9, 111.5, 111.9, 112.5, 112.9
tHPLHHO turnon propagation delayMODE = IIMHI rising to HOH rising40ns110.4, 110.8, 111.4, 111.8, 112.4, 112.8
tMONDelay matching LO on and HO offMODE = IIM12ns110.1, 111.1, 112.1, 110.12, 111.12, 112.12
tMOFFDelay matching LO off and HO onMODE = IIM4ns110.11, 110.13, 111.11, 111.13, 112.11, 112.13
tHRCHO rise timeCL = 1000pF10% to 90%7.5ns115, 116, 117
tLRCLO rise time7.5ns115.2, 116.2, 117.2
tHFCHO fall time90% to 10%5.5ns115.1, 116.1, 117.1
tLFCLO fall time5.5ns115.3, 116.3, 117.3
tPW_IIMMinimum input pulse width (turn-on)MODE = IIM8ns120, 120.2, 120.4, 121, 121.2, 121.4, 122, 122.2, 122.4
tPW_IIM_OFFMinimum input pulse width (turn-off)MODE = IIM12ns120.1, 120.3, 120.5, 121.1, 121.3, 121.5, 122.1, 122.3, 122.5
千亿体育app官网登录(中国)官方网站IOS/安卓通用版/手机APP | 米乐app下载官网（中国）|ios|Android/通用版APP最新版 | 米乐|米乐·M6（中国大陆）官方网站 | 千亿体育登陆地址 | 华体会体育（中国）HTH·官方网站 | 千赢qy国际_全站最新版千赢qy国际V6.2.14安卓/IOS下载 | 18新利网v1.2.5|中国官方网站 | bob电竞真人（中国官网）安卓/ios苹果/电脑版【1.97.95版下载】 | 千亿体育app官方下载(中国)官方网站IOS/安卓/手机APP下载安装 |