Calculation tool
SBAR013 — Isolated Amplifier Voltage Sensing Excel Calculator
This calculator provides estimates of the errors associated with using isolation amplifier devices in a voltage sensing configuration.
AMC3302
±50-mV input, precision current sensing reinforced isolated amplifier with integrated DC/DC
Data sheet
AMC3302
- 3.3-V or 5-V single supply with integrated DC/DC converter
- ±50-mV input voltage range optimized for current measurement using shunt resistors
- Fixed gain: 41
- Low DC errors:
- Offset voltage: ±50 µV (max)
- Offset drift: ±0.5 µV/°C (max)
- Gain error: ±0.2% (max)
- Gain error drift: ±35 ppm/°C (max)
- Nonlinearity: ±0.03% (max)
- High CMTI: 95 kV/µs (min)
- System-level diagnostic features
- Meets CISPR-11 and CISPR-25 EMI standards
- Safety-related certifications:
- 6000-VPK reinforced isolation per DIN VDE V 0884-11
- 4250-VRMS isolation for 1 minute per UL1577
- Fully specified over the extended industrial temperature range: –40°C to +125°C
The AMC3302 is a precision, isolated amplifier optimized for shunt-based current measurements. The fully integrated, isolated DC/DC converter allows single-supply operation from the low-side of the device, which makes the device a unique solution for space-constrained applications. The reinforced capacitive isolation barrier is certified according to VDE V 0884-11 and UL1577 and supports a working voltage of up to 1.2 kVRMS.
The isolation barrier separates parts of the system that operate on different common-mode voltage levels and protects the low-voltage side from hazardous voltages and damage.
The input of the AMC3302 is optimized for direct connection to a low-impedance shunt resistor or another low-impedance voltage source with low signal levels. The excellent DC accuracy and low temperature drift supports accurate current measurements over the extended industrial temperature range from –40°C to +125°C.
The integrated DC/DC converter fault-detection and diagnostic output pin of the AMC3302 simplify system-level design and diagnostics.
Technical documentation
No results found. Please clear your search and try again.
View all 47 Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
AMC3302EVM — AMC3302 evaluation module for ±50-mV-input precision reinforced isolated amplifier
The AMC3302 evaluation module (EVM) is a platform for evaluating the AMC3302, a precision isolated amplifier with an integrated DC/DC converter, which powers the high side of the amplifier. AMC3302 is a 7-kV reinforced isolated amplifier designed for use in current shunt measuring applications.
A (...)
Calculation tool
SBAR020 — Isolated Amplifier Current Sensing Excel Calculator
This calculator provides estimates of the errors associated with using isolation amplifier devices in a current sensing configuration.
Supported products & hardware
Products
Isolated amplifiers
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Reference designs
PMP22650 — GaN-based, 6.6-kW, bidirectional, onboard charger reference design
The PMP22650 reference design is a 6.6-kW, bidirectional, onboard charger. The design employs a two-phase totem pole PFC and a full-bridge CLLLC converter with synchronous rectification. The CLLLC utilizes both frequency and phase modulation to regulate the output across the required regulation (...)
Reference designs
TIDA-010210 — 11-kW, bidirectional, three-phase ANPC based on GaN reference design
This reference design provides a design template for implementing a three-level, three-phase, gallium nitride (GaN) based ANPC inverter power stage. The use of fast switching power devices makes it possible to switch at a higher frequency of 100 kHz, reducing the size of magnetics for the filter (...)
Reference designs
TIDA-010236 — 4-kW GaN totem-pole PFC reference design for appliances
This reference design is a 4-kW continuous conduction mode (CCM) totem-pole power factor correction (PFC) with a top-cooled gallium nitride (GaN) daughterboard and TMS320F280025C digital controller. Along with the integrated protection features of LMG352x and C2000, full protections are (...)
Design guide: PDF
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| SO-MOD (DWE) | 16 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.