Home Interface Ethernet ICs Ethernet PHYs
Home
Interface
Ethernet ICs
Ethernet PHYs
NEW

DP83TC811-Q1

ACTIVE

Low-power 100BASE-T1 automotive PHYTER™ Ethernet physical layer transceiver

Order now
Data sheet

DP83TC811-Q1

ACTIVE
Data sheet Order now

Product details

Datarate (Mbps) 100BASE-T1 Interface type MII, RGMII, RMII, SGMII Number of ports Single Rating Automotive Features 25-MHz clock out, Cable diagnostics, JTAG1149.1, Single supply, WoL I/O supply voltage (typ) (V) 1.8, 2.5, 3.3 Operating temperature range (°C) -40 to 125 Number of LEDs 2 ESD HBM (kV) 8
Datarate (Mbps) 100BASE-T1 Interface type MII, RGMII, RMII, SGMII Number of ports Single Rating Automotive Features 25-MHz clock out, Cable diagnostics, JTAG1149.1, Single supply, WoL I/O supply voltage (typ) (V) 1.8, 2.5, 3.3 Operating temperature range (°C) -40 to 125 Number of LEDs 2 ESD HBM (kV) 8
VQFN (RHA) 36 36 mm² 6 x 6
  • 100BASE-T1 – IEEE 802.3bw compliant
    • OPEN alliance qualified
    • Interoperable with BroadR-Reach and 100BASE-T1 PHYs
  • AEC-Q100 Qualified for automotive applications:
    • Device temperature grade 1: –40°C to +125 °C ambient operating temperature
    • Device HBM ESD classification level 3A
    • Device CDM ESD classification level C5 for all pins except pin 5
    • Device CDM ESD classification level C3 for pin 5
    • Device IEC61000-4-2 ESD classification level 4 for pins 12 and 13: ±8-kV contact discharge
  • MAC interfaces: MII, RMII, RGMII and SGMII
  • VQFN, wettable flank packaging
  • IEEE 1588 SFD support
  • Low transmit and receive latency for AVB/TSN
  • Low active power operation: < 230mW
  • Configurable I/O Voltages: 3.3V, 2.5V, and 1.8V
  • Power savings features:
    • Sleep, Standby and Disable
    • Wake-on-LAN (WoL)
  • Diagnostic tool kit
    • Signal Quality Indication (SQI)
    • Time Domain Reflectometry (TDR)
    • Electrostatic discharge sensor
    • Voltage sensor
    • Temperature sensor
    • PRBS Built-In Self-Test (BIST)
  • 100BASE-T1 – IEEE 802.3bw compliant
    • OPEN alliance qualified
    • Interoperable with BroadR-Reach and 100BASE-T1 PHYs
  • AEC-Q100 Qualified for automotive applications:
    • Device temperature grade 1: –40°C to +125 °C ambient operating temperature
    • Device HBM ESD classification level 3A
    • Device CDM ESD classification level C5 for all pins except pin 5
    • Device CDM ESD classification level C3 for pin 5
    • Device IEC61000-4-2 ESD classification level 4 for pins 12 and 13: ±8-kV contact discharge
  • MAC interfaces: MII, RMII, RGMII and SGMII
  • VQFN, wettable flank packaging
  • IEEE 1588 SFD support
  • Low transmit and receive latency for AVB/TSN
  • Low active power operation: < 230mW
  • Configurable I/O Voltages: 3.3V, 2.5V, and 1.8V
  • Power savings features:
    • Sleep, Standby and Disable
    • Wake-on-LAN (WoL)
  • Diagnostic tool kit
    • Signal Quality Indication (SQI)
    • Time Domain Reflectometry (TDR)
    • Electrostatic discharge sensor
    • Voltage sensor
    • Temperature sensor
    • PRBS Built-In Self-Test (BIST)

The DP83TC811-Q1 device is an IEEE 802.3bw-compliant automotive PHYTER™ Ethernet physical layer transceiver. The device provides all physical layer functions needed to transmit and receive data over unshielded single twisted-pair cables. The device provides xMII flexibility with support for standard MII, RMII, RGMII, and SGMII MAC interfaces.

This device includes the Diagnostic Tool Kit, providing an extensive list of real-time monitoring tools, debug tools and test modes. Within the tool kit is the first integrated electrostatic discharge (ESD) monitoring tool. The tool is capable of counting ESD events on both the xMII and MDI as well as providing real-time monitoring through the use of a programmable interrupt. Additionally, the DP83TC811-Q1 includes a pseudo random binary sequence (PRBS) frame generation tool, which is fully compatible with internal loopbacks, to transmit and receive data without the use of a MAC. The DP83TC811-Q1 is housed in a 6.00mm × 6.00mm, 36-pin VQFN wettable flank package.

The DP83TC811-Q1 device is an IEEE 802.3bw-compliant automotive PHYTER™ Ethernet physical layer transceiver. The device provides all physical layer functions needed to transmit and receive data over unshielded single twisted-pair cables. The device provides xMII flexibility with support for standard MII, RMII, RGMII, and SGMII MAC interfaces.

This device includes the Diagnostic Tool Kit, providing an extensive list of real-time monitoring tools, debug tools and test modes. Within the tool kit is the first integrated electrostatic discharge (ESD) monitoring tool. The tool is capable of counting ESD events on both the xMII and MDI as well as providing real-time monitoring through the use of a programmable interrupt. Additionally, the DP83TC811-Q1 includes a pseudo random binary sequence (PRBS) frame generation tool, which is fully compatible with internal loopbacks, to transmit and receive data without the use of a MAC. The DP83TC811-Q1 is housed in a 6.00mm × 6.00mm, 36-pin VQFN wettable flank package.
filter Find other Ethernet PHYs
Download View video with transcript Video

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 1
Type Title Date
* Data sheet DP83TC811-Q1 Low Power Automotive 100BASE-T1 Ethernet Physical Layer Transceiver datasheet (Rev. A) PDF | HTML 22 Apr 2024

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

DP83TC811EVM — DP83TC811 100BASE-T1 to 100BASE-TX automotive Ethernet PHY media converter evaluation module

The DP83TC811EVM is IEEE 802.3bw compliant, supporting 100BASE-T1. The DP83TC811R and DP83822H are configured in RGMII back-to-back, allowing a seamless media conversion from 100BASE-T1 to 100BASE-TX. This design has been tested and validated at UNH for 100BASE-T1 compliance.

The DP83TC811EVM (...)

User guide: PDF
Not available on TI.com
GUI for evaluation module (EVM)

DIEP — Debug Interface for Ethernet PHYs (DIEP)

The Linux drivers for Texas Instruments' Ethernet physical layer (PHY) transceivers support communication through the serial management interface (MDC/MDIO) to configure and read PHY registers.

The USB-2-MDIO software lets you directly access the registers during debug and (...)

Supported products & hardware

Supported products & hardware

Products
Ethernet PHYs
DP83822I — Low-power, robust 10/100-Mbps Ethernet PHY transceiver with 16-kV ESD DP83TC811-Q1 — Low-power 100BASE-T1 automotive PHYTER™ Ethernet physical layer transceiver DP83TC812R-Q1 — TC-10 compliant 100BASE-T1 automotive Ethernet PHY with RGMII DP83TC812S-Q1 — TC-10 compliant 100BASE-T1 automotive Ethernet PHY with RGMII & SGMII DP83TD510E — IEEE 802.3cg 10BASE-T1L Ethernet PHY DP83TG720R-Q1 — 1000BASE-T1 automotive Ethernet PHY with RGMII DP83TG720S-Q1 — 1000BASE-T1 automotive Ethernet PHY with RGMII & SGMII DP83822H — Extended temperature, robust low-power 10/100-Mbps Ethernet PHY transceiver with 16-kV ESD DP83822HF — Extended temperature, robust 10/100-Mbps Ethernet PHY transceiver with fiber support & 16-kV ESD DP83822IF — Low-power, robust 10/100-Mbps Ethernet PHY transceiver with fiber support & 16-kV ESD DP83825I — Smallest form factor (3-mm by 3-mm), low-power 10/100-Mbps Ethernet PHY transceiver with 50-MHz c DP83826E — Low latency 10/100-Mbps PHY with MII interface and enhanced mode DP83826I — Low latency 10/100-Mbps PHY, MII interface and enhanced mode with an industrial temperature range DP83848-EP — Enhanced Product PHYTER extreme temperature single port 10/100 Mb/s Ethernet physical layer DP83848C — Commercial temperature, 10/100-Mbps Ethernet PHY transceiver with SNI interface & JTAG support DP83848H — Extended temperature, 10/100-Mbps Ethernet PHY transceiver in a 40-pin QFN package DP83848I — Industrial temperature, 10/100-Mbps Ethernet PHY transceiver with SNI & JTAG support DP83848J — Commercial temperature, 10/100-Mbps Ethernet PHY transceiver in a 40-pin QFN package DP83848K — Industrial temperature, 10/100-Mbps Ethernet PHY transceiver in a 40-pin QFN package DP83867CR — Low-power, robust gigabit Ethernet PHY transceiver in a small QFN package DP83867IR — Industrial temperature, robust gigabit Ethernet PHY transceiver DP83867E — Extended temperature, robust low-latency gigabit Ethernet PHY transceiver with SGMII
Hardware development
Evaluation board
DP83822EVM — DP83822I 10-Mbps & 100-Mbps Ethernet PHY evaluation module DP83867ERGZ-R-EVM — DP83867ERGZ RGMII 1000M/100M/10M Ethernet PHY evaluation module DP83867ERGZ-S-EVM — DP83867ERGZ SGMII 1000M/100M/10M Ethernet PHY Evaluation Module DP83TD510E-EVM — DP83TD510E Low power 10Base-T1L single-pair Ethernet PHY evaluation module DP83TC812EVM-MC — DP83TC812 evaluation module for 100Mbs media converter DP83TC811EVM — DP83TC811 100BASE-T1 to 100BASE-TX automotive Ethernet PHY media converter evaluation module DP83TC811SEVM — DP83TC811S 100BASE-T1 automotive Ethernet PHY xMII evaluation module DP83TG720EVM-MC — DP83TG720 evaluation module for 1Gbps media converter DP83825EVM — Small form factor 10/100 ethernet PHY evaluation module DP83826EVM — DP83826 Low-latency 10/100 ethernet PHY evaluation module
Download
Simulation tool

PSPICE-FOR-TI — PSpice® for TI design and simulation tool

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Request
Simulation tool

TINA-TI — SPICE-based analog simulation program

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
User guide: PDF
View Options
Reference designs

TIDA-020047 — Two-device mmWave cascade reference design for automotive 4D imaging radar

This automotive radar reference design is a cascaded 76-GHz to 81-GHz radar sensor module. This includesa two-device cascaded array of AWR2243 devices and an AM2732R radar processor. In this cascaded radar configuration, a primary device distributes a 20-GHz local-oscillator (LO) signal to both (...)
Design guide: PDF
Package Pins CAD symbols, footprints & 3D models
VQFN (RHA) 36 Ultra Librarian
TI's Standard Terms and Conditions for Evaluation Items apply.

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring
Information included:
  • Fab location
  • Assembly location

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

View all forum topics

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos