Calculation tool
FET-INRUSH-SOA-CALC — FET SOA margin calculator for dvdt based startup
The design calculator allows user to estimate the FET SOA margin while starting up with dVdt based startup for inrush current control
TPS1210-Q1
Automotive 45-V low IQ dual high-side driver with short circuit protection and diagnostics
Data sheet
TPS1210-Q1
- AEC-Q100 automotive qualified for automotive applications
- Device temperature grade 1: –40°C to +125°C ambient operating temperature range
- Functional Safety-Capable
- 3.5-V to 40-V input range (45-V absolute maximum)
- Reverse input protection down to –40 V
- Integrated 11-V charge pump
- Low quiescent current, 35 µA in operation
- Low 1.5-µA shutdown current (EN/UVLO = Low)
- Two strong gate drivers (2A src/sink) for back-to-back MOSFET driving with separate control inputs (INP1, INP2)
- Variants with active high (TPS12100-Q1) and active low (TPS12101-Q1) inputs
- Adjustable short-circuit protection (ISCP) using external Rsense or MOSFET VDS sensing with adjustable delay (TMR)
- High or low-side current sense configuration (CS_SEL)
- Fault indication ( FLT) during short-circuit fault, charge pump under voltage, input undervoltage, and short-circuit comparator diagnosis (SCP_TEST)
- Adjustable input undervoltage lockout (UVLO)
The TPS1210x-Q1 family is a 45-V, low IQ, smart high side driver with protection and diagnostics. With wide operating voltage range of 3.5 V – 40 V, the device is designed for 12-V system designs. The device can withstand and protect the loads from negative supply voltages down to –40 V.
The device has two strong (2-A) GATE drivers with separate control inputs (INP1, INP2) to drive back-to-back MOSFETs in common source configuration. TPS12100-Q1 has active high control inputs and TPS12101-Q1 has active low control inputs.
The device provides adjustable short-circuit protection. Auto-retry and latch-off fault behavior can be configured. Current sensing can be done either by an external sense resistor or by MOSFET VDS sensing. High side or low side current sense resistor configuration is possible by using CS_SEL pin input. The device also features diagnosis of the internal short circuit comparator using external control on SCP_TEST input.
Low Quiescent current 35 µA (typical) in operation enables always ON system designs. Quiescent current reduces to 1.5 µA (typical) with EN/UVLO low.
The TPS1210x-Q1 is available in a 19-pin VSSOP package.
Technical documentation
No results found. Please clear your search and try again.
View all 2 | Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | TPS1210-Q1 45-V, Automotive Low IQ, Back-to-Back MOSFET Smart High Side Driver With Short-Circuit Protection and Diagnostics datasheet | PDF | HTML | 27 Oct 2023 |
| Functional safety information | TPS1210-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA | PDF | HTML | 02 Nov 2023 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
TPS4810Q1EVM — TPS4810-Q1 evaluation module for 3-V to 80-V low-IQ dual high-side driver with short-circuit protect
The TPS4810-Q1 evaluation module (EVM) is a platform for evaluating the reference circuit of the TPS4810-Q1 driver. TPS4810-Q1 is a 3-V to 80-V high-side controller and has two strong 2-A gate drivers with separate control inputs (INP1, INP2) to drive back-to-back metal-oxide-semiconductor (...)
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| VSSOP (DGX) | 19 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.