GUI for evaluation module (EVM)
TPS23882B
Type-3, two-pair, 8-channel PoE PSE controller with autonomous mode, SRAM and 200-mΩ RSENSE
Data sheet
TPS23882B
- IEEE 802.3bt PSE solution for PoE 2 Type-3 2-Pair power over ethernet applications
- Compatible with TI’s FirmPSE system firmware
- SRAM Programmable memory
- Programmable power limiting accuracy ±4%
- 200-mΩ current sense resistor
- User-selectable 15-W or 30-W autonomous mode with no MCU required
- Selectable 2-pair port power allocations
- 4 W, 7 W, 15.4 W, or 30 W
- Dedicated 14-bit integrating current ADC per port
- Noise immune MPS for DC disconnect
- 2% current sensing accuracy
- 1- or 3-bit fast port shutdown input
- Auto-class discovery and power measurement
- Never fooled 4-point detection
- Inrush and operational foldback protection
- 425-mA and 1.25-A selectable current limits
- Port re-mapping
- 8-bit or 16-bit I2C communication
- Flexible processor controlled operating modes
- Auto, semiauto and manual / diagnostic
- Per port voltage monitoring and telemetry
- –40 °C to +125 °C temperature operation
The TPS23882B is an 8-channel power sourcing equipment (PSE) controller engineered to insert power onto Ethernet cables in accordance with the IEEE 802.3bt standard. The PSE controller can detect powered devices (PDs) that have a valid signature, complete mutual identification, and apply power.
The TPS23882B improves on the TPS2388 with reduced current sense resistors, SRAM programmability, programmable power limiting, capacitance measurement, and compatibility with TI’s FirmPSE system firmware (see Device Comparison Table).
Programmable SRAM enables in-field firmware upgradability over I2C to ensure IEEE compliance and interoperability with the latest PoE enabled devices. Dedicated per port ADCs provide continuous port current monitoring and the ability to perform parallel classification measurements for faster port turn on times. A 1.25-A port current limit and adjustable power limiting allows for the support of non-standard applications above 60-W sourced. The 200-mΩ current sense resistor and external FET architecture allow designs to balance size, efficiency, thermal and solution cost requirements.
Port remapping and pin-to-pin compatibility with the TPS2388, TPS23880, and TPS23881 devices eases migration from previous generation PSE designs and enables interchangeable 2-layer PCB designs to accommodate different system PoE power configurations.
Similar products you might be interested in
Pin-for-pin with same functionality to the compared device
Technical documentation
No results found. Please clear your search and try again.
View all 6 | Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | TPS23882B Type-3 2-Pair 8-Channel PSE Controller with Autonomous Mode, SRAM, and 200-mΩ RSENSE datasheet (Rev. A) | PDF | HTML | 23 Feb 2022 |
| Application note | TPS23882B SIFOs IEEE802.3bt Conformance Test Report | PDF | HTML | 09 Aug 2023 | |
| Application brief | Choosing PoE PSE System Software Solutions | PDF | HTML | 03 Aug 2021 | |
| Application brief | Using the TPS23861 and TPS23882B in Autonomous Mode Features and Benefits | PDF | HTML | 30 Jul 2021 | |
| EVM User's guide | TPS23882B1EVM: PoE, PSE, TPS23882B1 Evaluation Module | PDF | HTML | 29 Apr 2021 | |
| Certificate | TPS23882B1EVM-008 EU RoHs Declaration of Conformity (DoC) | 23 Apr 2021 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
BOOST-PSEMTHR8-097 — TPS23882 Type-3, 30W, 2-pair, PSE motherboard for 8-port PSE systems
This motherboard is the base board for the PSE Controller ecosystem. The octal channel, TPS23882, IEEE 802.3bt ready PoE PSE controller can be evaluated by using the motherboard (BOOST-PSEMTHR8-097) and TPS23882EVM daughter card (TPS23882EVM-008) (sold separately). The full PoE Evaluation ecosystem (...)
User guide: PDF
Daughter card
TPS23882B1EVM-008 — TPS23882B daughter card type-3, 30-W, two-pair, eight-port system PSE
The TPS23882B1EVM-008 daughter card features an eight-channel, IEEE 802.3bt ready (Type-3, 30-W) 2-pair PSE controller.
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| VQFN (RTQ) | 56 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.