ZHCSNB8A February   2021  – January 2024 BQ25730

PRODUCTION DATA  

  1.   1
  2. 特性
  3. 应用
  4. 说明
  5. 说明(续)
  6. Device Comparison Table
  7. Pin Configuration and Functions
  8. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics(BQ25730)
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Power-Up Sequence
      2. 8.3.2  Two-Level Battery Discharge Current Limit
      3. 8.3.3  Fast Role Swap Feature
      4. 8.3.4  CHRG_OK Indicator
      5. 8.3.5  Input and Charge Current Sensing
      6. 8.3.6  Input Voltage and Current Limit Setup
      7. 8.3.7  Battery Cell Configuration
      8. 8.3.8  Device HIZ State
      9. 8.3.9  USB On-The-Go (OTG)
      10. 8.3.10 Converter Operation
      11. 8.3.11 Inductance Detection Through IADPT Pin
      12. 8.3.12 Converter Compensation
      13. 8.3.13 Continuous Conduction Mode (CCM)
      14. 8.3.14 Pulse Frequency Modulation (PFM)
      15. 8.3.15 Switching Frequency and Dithering Feature
      16. 8.3.16 Current and Power Monitor
        1. 8.3.16.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 8.3.16.2 High-Accuracy Power Sense Amplifier (PSYS)
      17. 8.3.17 Input Source Dynamic Power Management
      18. 8.3.18 Input Current Optimizer (ICO)
      19. 8.3.19 Two-Level Adapter Current Limit (Peak Power Mode)
      20. 8.3.20 Processor Hot Indication
        1. 8.3.20.1 PROCHOT During Low Power Mode
        2. 8.3.20.2 PROCHOT Status
      21. 8.3.21 Device Protection
        1. 8.3.21.1 Watchdog Timer
        2. 8.3.21.2 Input Overvoltage Protection (ACOV)
        3. 8.3.21.3 Input Overcurrent Protection (ACOC)
        4. 8.3.21.4 System Overvoltage Protection (SYSOVP)
        5. 8.3.21.5 Battery Overvoltage Protection (BATOVP)
        6. 8.3.21.6 Battery Discharge Overcurrent Protection (BATOC)
        7. 8.3.21.7 Battery Short Protection (BATSP)
        8. 8.3.21.8 System Undervoltage Lockout (VSYS_UVP) and Hiccup Mode
        9. 8.3.21.9 Thermal Shutdown (TSHUT)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Forward Mode
        1. 8.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 8.4.1.2 Battery Charging
      2. 8.4.2 USB On-The-Go
      3. 8.4.3 Pass Through Mode (PTM)-Patented Technology
    5. 8.5 Programming
      1. 8.5.1 I2C Serial Interface
        1. 8.5.1.1 Timing Diagrams
        2. 8.5.1.2 Data Validity
        3. 8.5.1.3 START and STOP Conditions
        4. 8.5.1.4 Byte Format
        5. 8.5.1.5 Acknowledge (ACK) and Not Acknowledge (NACK)
        6. 8.5.1.6 Target Address and Data Direction Bit
        7. 8.5.1.7 Single Read and Write
        8. 8.5.1.8 Multi-Read and Multi-Write
        9. 8.5.1.9 Write 2-Byte I2C Commands
    6. 8.6 Register Map
      1. 8.6.1  ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
      2. 8.6.2  ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
        1. 8.6.2.1 Battery Pre-Charge Current Clamp
      3. 8.6.3  ChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
      4. 8.6.4  ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
      5. 8.6.5  ProchotStatus Register (I2C address = 23/22h) [reset = B800h]
      6. 8.6.6  IIN_DPM Register (I2C address = 25/24h) [reset = 4100h]
      7. 8.6.7  ADCVBUS/PSYS Register (I2C address = 27/26h)
      8. 8.6.8  ADCIBAT Register (I2C address = 29/28h)
      9. 8.6.9  ADCIIN/CMPIN Register (I2C address = 2B/2Ah)
      10. 8.6.10 ADCVSYS/VBAT Register (I2C address = 2D/2Ch)
      11. 8.6.11 ChargeOption1 Register (I2C address = 31/30h) [reset = 3F00h]
      12. 8.6.12 ChargeOption2 Register (I2C address = 33/32h) [reset = 00B7]
      13. 8.6.13 ChargeOption3 Register (I2C address = 35/34h) [reset = 0434h]
      14. 8.6.14 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A81h(2S~5s) 4A09(1S)]
      15. 8.6.15 ProchotOption1 Register (I2C address = 39/38h) [reset = 41A0h]
      16. 8.6.16 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
      17. 8.6.17 ChargeOption4 Register (I2C address = 3D/3Ch) [reset = 0048h]
      18. 8.6.18 Vmin Active Protection Register (I2C address = 3F/3Eh) [reset = 006Ch(2s~5s)/0004h(1S)]
      19. 8.6.19 OTGVoltage Register (I2C address = 07/06h) [reset = 09C4h]
      20. 8.6.20 OTGCurrent Register (I2C address = 09/08h) [reset = 3C00h]
      21. 8.6.21 InputVoltage(VINDPM) Register (I2C address = 0B/0Ah) [reset =VBUS-1.28V]
      22. 8.6.22 VSYS_MIN Register (I2C address = 0D/0Ch) [reset value based on CELL_BATPRESZ pin setting]
      23. 8.6.23 IIN_HOST Register (I2C address = 0F/0Eh) [reset = 2000h]
      24. 8.6.24 ID Registers
        1. 8.6.24.1 ManufactureID Register (I2C address = 2Eh) [reset = 40h]
        2. 8.6.24.2 Device ID (DeviceAddress) Register (I2C address = 2Fh) [reset = D5h]
  10. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Input Snubber and Filter for Voltage Spike Damping
        2. 9.2.2.2 ACP-ACN Input Filter
        3. 9.2.2.3 Inductor Selection
        4. 9.2.2.4 Input Capacitor
        5. 9.2.2.5 Output Capacitor
        6. 9.2.2.6 Power MOSFETs Selection
      3. 9.2.3 Application Curves
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
      1. 11.2.1 Layout Example Reference Top View
      2. 11.2.2 Inner Layer Layout and Routing Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 第三方米6体育平台手机版_好二三四免责声明
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 接收文档更新通知
    4. 12.4 支持资源
    5. 12.5 Trademarks
    6. 12.6 静电放电警告
    7. 12.7 术语表
  14. 13Revision History
  15. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Revision History

Changes from Revision * (February 2021) to Revision A (January 2024)

  • 向特性中添加了 IEC 62368-1 CB 认证Go
  • Changed pin name from OT/VAP/FRS to OTG/VAP/FRS in Table 6-1 Go
  • Changed VSYS_MIN_REG_ACC from REG0x3E to REG0x0D/0C in Section 7.5 Go
  • Updated Section 8.3.5 Go
  • Changed from REG0x15 to REG0x04 in Section 8.3.7 Go
  • Changed < and > in Section 8.3.16.2 Go
  • Changed from REG0x34 to REG0x38 and voltage rises above to voltage falls below in Section 8.3.20.1 Go
  • Changed IIN_DPM() Description from 50 mA to 100 mA in Table 8-7 Go
  • Updated WDTMR_ADJ and IIN_DPM_AUTO_DISABLE Descriptions in Table 8-8 Go
  • Updated EN_CMP_LATCH and EN_LDO Descriptions in Table 8-9 Go
  • Changed from REG0x15 to REG0x05/04 in Section 8.6.3 Go
  • Changed from REG0x21 to REG0x22 in IN_VAP Description in Table 8-14 Go
  • Deleted not from 1b in IN_IIN_DPM Description in Table 8-14 Go
  • Changed from REG0x23[7,2],REG0x23[6:0] to REG0x22 and cleared to reset in Section 8.6.5 Go
  • Changed from TSHUT to Reserved and updated STAT_EXIT_VAP Description in Table 8-16 Go
  • Changed from 128mA to 256mA and REG0x14 to REG0x02 in AUTO_WAKEUP_EN Description in Table 8-29 Go
  • Changed from Vmin Active Protection to VSYS_TH1 and from REG0x37 to REG0x36 in Section 8.6.14 Go
  • Changed from 0x22H to 0x25/24 in ILIM2_VTH Description and from REG0x33 to REG0x36 in PROCHOT_VINDPM_ 80_90 Description in Table 8-34 Go
  • Changed from REG0x3D to REG0x0B/0A in LOWER_PROCHOT_ VINDPM Description in Table 8-35 Go
  • Changed IDCHG_DEG1 Reset from 00b to 01b in Table 8-36 Go
  • Changed from 0b to 1b in PP_VBUS_VAP Description in Table 8-40 Go
  • Changed from REG37 to REG0x3E in EN_VSYSTH2_FOLLOW_VS YSTH1 Description in Table 8-43 Go
  • Changed from REG0x09 to REG0x09/08 in Section 8.6.20 and values in bit descriptions in Table 8-46 Go
  • Changed from REG0x3E to REG0x0D/0C in Section 8.6.22 Go
  • Updated third paragraph in Section 8.6.23 Go