4 Revision History

Changes from F Revision (May 2018) to G Revision

• Changed references to HDMI2.0a to HDMI2.0b Go
• Added links to end equipment pages in Applications section.Go

Changes from E Revision (April 2018) to F Revision

• Changed From: "SN75DP159 is characterized from –40°C to 85°C" To "SN65DP159 is characterized from –40°C to 85°C" in the Description (continued)Go
• Changed From: "SN65DP159 is characterized from 0°C to 85°C" To "SN75DP159 is characterized from 0°C to 85°C" in the Description (continued)Go

Changes from D Revision (June 2017) to E Revision

• Changed the pinout images appearance in the Pin Configuration and Functions sectionGo

Changes from C Revision (July 2016) to D Revision

• Changed the title From: " SNx5DP159 6-Gbps DP++ to HDMI Retimer" To: "SNx5DP159 6-Gbps AC-Coupled TMDS™ to HDMI™ Level Shifter Retimer"Go
• Changed the Features ListGo
• Changed the Applications ListGo
• V_SADJ: Added Note: "Best transmit eye ..", added MIN and MAx values in the Recommended Operating Conditions table Go
• Changed the description of t_d1 in Table 1Go
• Changed read procedures in the I²C Control Behavior sectionGo
• Added paragraph: "DP159 is designed..." to the Application and Implementation sectionGo
• Added 2 paragraphs to the Application Information sectionGo
• Added line item "Adding pre-emphasis will improve..." to the Detailed Design Procedure sectionGo

Changes from B Revision (Arpil 2016) to C Revision

• Recommended Operating Conditions, Changed the CONTROL PINS sectionGo
• Changed the AUX, DDC, and I2C Electrical Characteristics tableGo
• Added text to Figure 31 Note: "The SCL_SRC and SDA_SRC pins must be pulled to ground."Go

Changes from A Revision (July 2015) to B Revision

• Added "Low-level input voltage at OE" to V_IL in the Recommended Operating Conditions tableGo
• Added OE to V_IH "High-level input voltage" in the Recommended Operating Conditions tableGo
• Changed Figure 22Go
• Deleted the VDD_ramp and VCC_ramp MIN values in Table 1Go
• Changed text "through the I²C interface" To: "through the I²C access on the DDC interface" in DDC Functional DescriptionGo
• Changed the HDMI and DVI value for 1Ah Table 3Go
• Added Note to 11–400-kbps in Table 7Go
• Changed the note in the DEV_FUNC_MODE section of Table 7Go
• Changed Note in the DDC_TRAIN_SET section of Table 8Go

Changes from * Revision (July 2015) to A Revision

• Updated device status from product preview to production data Go
• Updated Typical Power Number Go
• Removed Standby Power numbers Go
• Changed From: Preview To: Production data Go
• Replaced SIG_EN with NC in pinout drawing and Pin Functions tableGo
• Removed lane swap from description of SWAP/POL = H Go
• Updated swing data Go
• Changed DDC link into its pin names between SNK and SRC and updated min value Go
• Added new line for SCL_SNK, SDA_SNKGo
• Removed standby power and standby current rows and updated active power and current numbers Go
• Changed term control to no source termination Go
• Increased I_LEAK max value from 10 µA to 45 µAGo
• Updated redriver mode max jitter value Go
• Clarified polarity swap to input signals Go
• Added more information on compliance in redriver mode Go
• Added note to DDC Functional Description section describing DDC snoop function Go
• Removed bit 4 SIG_EN and made reserved Go
• Removed SIG_EN Pin and added Note 1 for DDC Snoop Go
• Updated schematic to replace SIG_EN pin with NC Go
• Updated VID swing Go
• Changed Title to better match table. Removed Standby and redundant rowsGo
• Updated drawing with pin 17 changed to NC Go