Calculation tool
Data sheet
TPS40200
- Input Voltage Range 4.5 V to 52 V
- Output Voltage (700 mV to 90% VIN)
- 200-mA Internal P-channel FET Driver
- Voltage Feed-Forward Compensation
- Undervoltage Lockout
- Programmable Fixed-Frequency (between 35 kHz
and 500 kHz) Operation - Programmable Short-Circuit Protection
- Hiccup Overcurrent Fault Recovery
- Programmable Closed-Loop Soft-Start
- 700 mV 1% Reference Voltage
- External Synchronization
- Small 8-Pin SOIC (D) and VSON (DRB) Packages
The TPS40200 is a flexible, non-synchronous controller with a built-in 200-mA driver for P-channel FETs. The circuit operates with inputs up to 52 V with a power-saving feature that turns off driver current once the external FET has been fully turned on. This feature extends the flexibility of the device, allowing it to operate with an input voltage up to 52 V without dissipating excessive power. The circuit operates with voltage-mode feedback and has feed-forward input voltage compensation that responds instantly to input voltage change. The integral 700-mV reference is trimmed to 2%, providing the means to accurately control low voltages. The TPS40200 is available in an 8-pin SOIC and an 8-pin VSON package and supports many of the features of more complex controllers. Clock frequency, soft-start, and overcurrent limits are each easily programmed by a single, external component. The part has undervoltage lockout, and can be easily synchronized to other controllers or a system clock to satisfy sequencing and/or noise-reduction requirements.
Technical documentation
No results found. Please clear your search and try again.
View all 6 | Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | TPS40200 Wide Input Range Non-Synchronous Voltage Mode Controller datasheet (Rev. G) | PDF | HTML | 01 Dec 2014 |
| Selection guide | Power Management Guide 2018 (Rev. R) | 25 Jun 2018 | ||
| Application note | Automated Frequency Response Analyzer | 09 Oct 2013 | ||
| Analog Design Journal | 3Q 2010 Issue Analog Applications Journal | 11 Aug 2010 | ||
| EVM User's guide | Using the TPS40200EVM-002 with a 24V Input (Rev. B) | 07 Apr 2009 | ||
| More literature | TPS40200D Test Report | 15 Feb 2008 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
TPS40200EVM-002 — Evaluation Module for a 24V Input
The TPS40200EVM-002 evaluation module (EVM) uses the TPS40200 non-synchronous buck controller to provide a resistor selected 3.3 V output voltage that delivers up to 2.5 A from a 24 V input bus. The EVM operates from a single supply and uses a single P-channel power FET and Schottky (...)
User guide: PDF
Development kit
LAUNCHXL-F28027 — C2000 Piccolo MCU F28027 LaunchPad™ development kit
LAUNCHXL-F28027 is a low cost evaluation and development tool for the F2802x series in the TI MCU LaunchPad ecosystem which is compatible with various plug-on BoosterPacks (suggested under the Recommended BoosterPacks in the Features section below). The LaunchPad provides a standardized and (...)
User guide: PDF
Simulation model
TPS40200 TINA-TI Transient -5.2V Buck/Boost Reference Design
SLVM023.ZIP (135 KB) - TINA-TI Reference Design
Simulation model
TPS40200 TINA-TI AC Analysis Reference Design (Rev. D)
SLVJ005D.TSC (795 KB) - TINA-TI Reference Design
Simulation model
TPS40200 TINA-TI Average Spice Model (Rev. B)
SLVM024B.ZIP (11 KB) - TINA-TI Spice Model
Simulation model
TPS40200 TINA-TI Transient Buck Reference Design
SLVM022.ZIP (44 KB) - TINA-TI Reference Design
Simulation model
TPS40200 Unencrypted PSpice Average Model Package (Rev. E)
SLVJ006E.ZIP (332 KB) - PSpice Model
Reference designs
PMP30595 — Universal buck converter reference design for educational purposes
This universal buck converter reference design features a voltage mode buck converter in combination with a tiny, onboard electronics load to demonstrate the relationship in-between small-signal analysis in frequency domain (network analysis) and large signal analysis in time domain (transient (...)
Reference designs
PMP10070 — Power Supply for Sensitive Loads and Input Voltages Smaller, Equal or Bigger than the Output Voltage
This reference design is based on the ZETA topology for having very low output ripple. An input voltage between 8V and 16V generates an output voltage of 12V with a load of 1.5A.
Reference designs
TIDM-LPBP-LEDDRIVER — Real-time Digital LED Control
The Real-time Digital LED Control reference design demonstrates the control of three boost converters to drive three LEDs (red, blue, and green) strings. This design allows development with real-time digital control of the various LEDs which makes it perfect for any industrial or automotive (...)
Schematic: PDF
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| SOIC (D) | 8 | Ultra Librarian |
| VSON (DRB) | 8 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.